GDT655SGJ5BB General Electric Dishwasher - Instructions

Didn't actually do the compete repair but got close. Pulled out dishwasher, disconnected and checked continuity on the existing heating element (about 16 ohms) the new element was also about 16 ohms. This indicates they both were working fine and no need for replacement. Next step would have been to swap the elements would have been simple. Tried to replace main board as well, still not the issue so giving up and replacing the dishwasher. It wasn't the high temp cut off thermostat either incidentally and no error codes in maintenance mode. Check continuity of your existing element before ordering to save aggravation.

Open the washer, remove the bottom dish rack, then twist off the bottom water sprayer. Use a screwdriver to remove the mounting/ stabilizing screws so you can slide out the dishwasher. Close the dishwasher and slide it out. Underneath at the back there are two wires powering the drying element, carefully remove them. Use an adjustable wrench to remove the two plastic mounting nuts for the drying element. Open the washer and remove the old drying element, and insert the new element. Reassemble the dishwasher in the reverse order if disassembly.

1. Turn off breaker supplying power to dishwasher in electrical panel
2. Open dishwasher door
3. Unscrew the screws that secure the dishwasher to the counter.
4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch.
5. On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside.
6. Remove old door latch.
7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in.
8. Plug wire harness into new door latch.
9. Re-align dishwasher and re-secure to counter in previous position.
10. Test latch to make sure it closes properly.
11. Turn on breaker in electrical panel.
The dishwasher should now function properly.

1. Pull out dishwasher (not all the way) 2. Open the door. 3. Remove the white rope holding the door hinge (both sides) 4. Remove the door by pulling up when the door is open about 4-8 inches. 5. Lay the door on the floor ( put something under the door so not to scratch the front. 6. Remove the small bolt at the bottom of the door (both sides). 7. Slide the hinge back, up, then out. 8. Where the hinges were are another set of bolts, remove those (both sides) 9. Grab the top part of the door (the part with the buttons) and slide apart. 10. Remove the styrofoam carefully. 11. Disconnect the wiring harness. 12. Remove the 6 screws holding the Despenser tray in place. 13. Put in new Despenser tray and put everything back together.

repair under warranty for Home Depot. Ordered new controller, new sump manifold, new piranh clamp kit, new diverter passive main assy, installation took 6 months. Could not finish as GE had changed the diverter to a new design with the same part number that the repairman had no knowledge of and there is no part available for the same configuration of the one that went bad, after I called GE tech line they were not aware of updates. Giving me the same numbers. The new design works if you order a new conduit main. As the old one in the dishwasher will not connect to the new Diverter. New deverter no. WD19X25278 and the new main conduit is the same as the old configuration no.WD12X21681 . The repair people and parts people are not yet aware of the design change and availability of parts, as most are out of stock and no updated pictures of the new design. Repair warranty washed their hands of this and Home Depot after 6 months gave me credit of my full price I bought this for 3 yrs ago. Repairing myself and sell.

I first tested for 120volts to my dishwasher to verify it was getting power from my electrical panel. Then tested pins 2 and 5 on the control board to make sure there was 14 volts going to the user interface harness. After I verified that I knew it was the user interface that was bad. I watched a video I found on YouTube and followed it. This repair was fairly easy while watching the video and making sure that you use the correct pin out that comes in the box for your model. I’m not an appliance repair person and it took me about an hour start to finish. I’m going to attach the video I https://youtu.be/TI8cUjy5YOE

https://www.youtube.com/watch?v=GN5t4VFgLCY

I listened to the DW cycles to be sure it was the drain pump (no water passes through discharge tube). We already had checked inside filter and our drain line. I watched video and saw it was a simple change. We unplugged and removed the pump and the new one fit exactly-it came with several clamps. Very simple & effective!

Disconnect the power and turn off water.I took the whole dishwasher out ,laid it on its side.I then unscrew the bracket that holds the pump in place.then took off the two hose clamps and took off the pump.I then installed the new pump with the new pump and hose clamps from the new kit I got.when I looked at the old pump I noticed it comes apart so I open it and noticed a toy ring gemstone price of plastic was stuck inside the pump.So at w I found out what the problem was.I was very happy that all went so wellin putting all back together and it worked. Thanks so much made me and wife happy.

Replaced transition piece, gasket, and vent cover. The root cause problem is that the factory installed gasket was too thick and would not allow sufficient thread engagement. The replacement gasket was about 25% thinner and worked perfectly.

We bought this GE dishwasher new. After 9 months, we started noticing the dishes were not cleaning well. Eventually, the machine just filled up with water and drained. The washing arms didn't work. I replaced fill valve, but that didn't solve it. A GE Tech ran a diagnostic and informed us the pump motor was bad. It was off warranty and repairs would be $300. However, he noted it was easy to do on my own. Two pipe clamps. The part from PartsSelect was 40% less than ordering from GE and was a GE part. Replacement took half an hour and that includes getting it wrong once (one connection leaked due to a bad job attaching the pipe clamp). Works like a champ now.

Standard repair process to replace UI. The piece worth noting is the strange behavior on initial install. After setting the jumpers to the correct pins for my model based on the instructions, the board would initially not respond. It was only after i change the jumpers to a setting for another model and put power on the board that i got a response. I then set the jumpers back to the pins for my model that the board began to respond normally. Its been fine since.

Took old valve assembly off and replaced with new assenbly

just bolted on the new one and hooked up the hose

Replaced heating element. This was the path of least resistance but the problem persisted. I tried resetting the dishwasher but still nothing. My last resort is the circuit board. I checked the relays on the old board and they are fine so it must be something else on the circuit board. The dishwasher is not really that old (4 years) and everything else is fine. Just ordered the board so I really hope this fixes the problem.

I got lucky and found the diagnostic test instructions tucked inside the washer under the kick plate. From there I ran the tests on each component until I narrowed it down to the pump. The pump cost me less than local dealers. The install went well. Watched the online videos to make sure I was doing it right. Was actually very easy and saved hundreds over a service call.