GSD4060K55SS General Electric Dishwasher - Instructions

Simply removed the old rack and installed the new rack.....easy as 123 ABC. Dishwasher still works fine but the bottom rack had rusted out. Not sure if this is common for this Hotpoint dishwasher as my deciding factor to order from here was that others had the same problem as me.

I lifted out the old baffles, cleaned the soap scum from the recesses, and placed the new baffles in by hand. No tools were required, and total repair time was less than 8 minutes. the total cost was a fraction of the cost of a service call.

Replaced both corner tub baffles but did not correct the problem.

It was so easy-just popped the end peice in and it fit perfectly. I also ordered 2 knobs for my dryer which was only one year old, they were also so easy to put on.. I received my parts 2 days after I ordered and because of some problems with my computer had to talk to the operators and was very pleased and happy with their help and with the parts that I ordered. I wil always order my parts from Parts Select.

This is erins dad. She just bought her first home and it was missing the basket. I went online found your company and ordered.

Replaced both left and right baffle and the problem seems to be corrected. Very simple without the assistant of a professional.

Just remove the lower basket from the machine and pull the old wheels off. Then snap on the new wheels on the pegs. The old style wheels snap in place without much force. The new wheels take much more force to install and lock onto the basket which keeps them from coming off when the basket is heavily loaded.

Simply remove both baffles by hand, wash space under baffles with warm water and dry, then insert new ones which fit perfectly and were tight.

Removed old parts and installed the new ones.

Put end cap in dishwasher with movable part toward the back of the dishwasher. The free end of the movable part should be oriented at the top of the end cap. Put the lower half of the end cap into the rail behind the indented metal area so the widest part of the end cap is just opposite the hole where it should snap into place. Push the movable arm towards the back of the dishwasher until it fits under the upper rail. Then move the top half of the end cap into place under the top of the rail.

I ordered a drain valve shaft seal and new push on nut after reading similar stories of leaking problems on-line. I was pretty sure the leak was coming from the dump valve seal.

With repair parts on-hand, I took my dishwasher out during kitchen remodeling. I put the dishwasher on it's left side and removed the solenoid rod (lifts out on its own) and the dump valve's white plastic lever. I removed the old push on nut and pulled out the old washer with a small screwdriver. I then installed the new washer paying close attention to the supplied directions that said to install it with the lip in the correct direction. I then slipped on the new push on nut. The new push on nut is necessary since the old one will be destroyed in trying to remove it. I attacked it with needle nose plyers, a nail, and a small screwdriver before getting it bend and become loose enough to slide off. Care must be taken not to damage the shaft and groove. If you are generally handy at repairs, this repair will be easy.

I just hooked it up a few days ago and ran a cycle and no leak. Countertops will be installed in 4 days and the dishwasher will then get used frequently. I have faith the repair will hold and the dishwasher will remain leak free.

Luckily PartSelect was available to order the $20 repair parts and keep my faithful dishwasher on-line. Saved me the cost of a new $500 unit. I know this dishwasher cleans well and I don't have to risk buying a new one just to find out it doesn't clean as well.

The baffles looked worn so I started with replacing both of those. This did reduce the leaking from the left corner but did not totally stop it. I then decided to replace the door gasket so I put in an order for one and it came the following day. This was also very easy (no tools required). I just cleaned really good and dried the area and put the new door gasket in. NO MORE LEAK! We are getting ready to sell our home and this saved us from having to buy a new dishwasher. Thanks PartSelect:)

I measured the diameter of the working wheels from the existing ones, and located the parts I needed from the website. I order two packages, each containing the wheels and axles for the rack.
When delivered, I snapped the wheels onto the delivered axles. Then, I snapped the axels unto the bottom rack, at the correct place. I used a large pliers for leverage because the axel was a bit tight to just simply snap on.
The middle wheels are located just behind the front wheels, thereby offering support when the botton rack is pulled forward for loading. Likewise, they offer support when the rack is pushed back in place.

Simply took out old and put in new

This is the second time I have order a part from this firm. They have been kind, helpful and sent my order to me immediately. The first part was a wheel for the dish rack in the dish washer. The second part was an end cap for the dish rack slide. I installed the parts within a minute. I am very pleased with their professional service and highly recommend them to anyone with an appliance problem where parts are needed quickly.