GDT535PSM0SS General Electric Dishwasher - Instructions

I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..

Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher

Researched what others have posted about on Parts select. That really helped with the diagnosis! Took a chance on a $28 part. Repairman was going to charge $150 just to show up, then diagnose, leave for 2 months while waiting for the part, charge another $150 plus the part to fix…
Just had to pull out dishwasher far enough to take the water supply line off. Then the water inlet solenoid then 2 more screws and a 2 pronged plug reattach water supply then done! 15 minutes MAX!!!

Since I have granite countertops, unscrewed 2 screws on each side of cabinet. Unscrewed the toe plate, unplugged the wire connector, and disconnected the cable
from the door which was held by tie wraps. Pulled out dishwasher about a foot. Unhooked the spring cable to the door, lifted the door out and placed it on a spare table. With door face down on a towel, I unscrewed the screws at the bottom to release the latches, then unscrew the screws that hold the door locked in place. Turned the door on its back face up, wedged a flathead driver to release the settings display, from the body of the door. Separated the 2 panels replaced the foam rubber vent seal. Placed the face face down, reconnected both pieces of the door together pushing down. Rescrewed the bottom to lock the 2 pieces together reinsert the hinges, screwed them in with nutdriver1/4". Grabbed the old gasket, replaced it with new one, sliding it into the groove on the bottom inside of door. Reattached the door to the washer, rehooked the cables to the door, retired with zip ties the cable to the underside of door, reinstalled the wire connector, and re screwed the toe plate. Pushed the dishwasher, leveled, rescrewed into cabinet. Replaced the tub gasket.

1. Shut off circuit breaker power
2. remove toekick
3 .disconnect door wire harness at bottom of main control board
4. release 2 wire ties securing harness to tub using long nose pliers
5. remove 2- 1/4 in. hex head screws from bottom of door
6. insert 5/32 in Allen wrench through existing holes in front leg and hinge arm when door is partially opened.(about 1/4 of the way)
7. repeat step 6 on both sides (this locks door partially open)
8. lift door up about 3 in. then tilt door in and remove door completely
9. slide old gasket out and replace with new gasket
9. reassemble door

So easy, even I was able to do it. Slide tabs back on defective basket and remove both sides, then slide the tabs onto new basket and place in dishwasher. All Done!

Part was incorrect Compare that to GE site saying number on both ports to different parts try to return was half the course of what I paid ridiculous So apparently I'm stuck with it Check GE site you'll see the port is different from what your sound but the numbers are exactly the same No clips to support the utensil tray

Quite simple. Only disassembly/reassembly was the spray mechanism attached to the bottom of the Upper Rack. Snaps off old and on to new rack with no tools. On this dishwasher model, there is no hose assembly running to water port, but the spray assembly is instead a integrated tube with a male port that "plugs" into a female port on back of unit. Definitely get 2 end caps.
Only difference from original, is the design of the bottom rack. To fit such that the door closes, the silverware rack is at the back of the unit versus the front. Somewhat inconvenient. Can put silverware rack in front, but then less efficient for dishes.

Seems to be a common issue - what is not mentioned is how poor this vendor is at processing returns and how long it takes. It took them 2 weeks to acknowledge my return request which was sent the same day the part arrived - and now they say it could take another 90 days because it is a GE component. I have installed electronic boards in so many devices and even have custom built PC's without an issue (unless the board arrives defective - like this one did! The board arrived dead and the anti-static wrap was previously opened (tape was ripped and not secure). I took some pictures and like the other commenter, my old UI board worked/lights up just fine but will not stay that way for more than a few days (and then have to power cycle the main board until it comes back on). It is annoying - but this supposedly brand new (factory tested my @$$) board will not light up or beep at all! It will go back and will also file a dispute with PayPal if these folks continue to drag their feet. I would stay away from this part - nobody else even has this in stock - but somehow they have access to a pile of defective boards...

Replaced the dishwasher with a new one! used the same brand (GE) but different model to make the job a little easier, first cut power to the outlet, disconnected electrically from dishwasher, cut off water source from dishwasher, and disconnected hose from garbage disposal, removed old dishwasher put new one in, connected electrical wires (color coded), connected water supply with pliers, and connect your hose to your disposal and level your new disposal with leveling screws that comes with the new dishwasher. Put front cover plate on with screws provided with a screwdriver and that's it.

Parts diagram shows Striker can be popped out with screwdriver. Not true. It has a screw bolting it internally. Impossible to get to unless you disassemble the entire door. We took a power drill and small drill bit and bore it out like a cavity in a tooth. Needle nose pliers to extract the screw. Pretend your a dentist. Fixed it in 5 minutes. Replacement fit tight. A+

The repair was just like the video that the agent sent me. And while I had the unit out of the cabinet I installed a part I have had for months which I ordered before I realized I had to take the unit out of the cabinet: the part was the seal for the bottom of the door. I recommend if you are ordering a pump order this part too an it is easy to install if you already have the dishwasher out of the cabinet.

We I installed a new dishwasher pump. It was simple and easy. I did it myself. My husband removed the clamps holding the dishwasher in the cabinet. Then he turned it in it's side and I replaced the old pump for an identical one that I ordered from this site. Easy peasy, took all of 15 minutes. You've got this. Don't call a repair man and pay $300 or buy a new dishwasher and pay $800. This repair was $63. If I can do it, you can!!!

Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!

The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.