ADW1100NW General Electric Dishwasher - Instructions

door gasket dried out due to not using the dishwasher very often and needed to be replaced. removed door, replaced gasket, and re-installed door.

Water was leaking from under refer next to installed under counter dishwasher. Once determined to be dishwasher not refer I removed dishwasher toe place was able to see dripping inlet solenoid valve. I had to disconnect 11V power, shut off inlet water, disconnect inlet water house and remove dishwasher from under counter. Once dishwasher was in center of kitchen I flipped it upside down and removed the electric solenoid inlet valve. Removing the valve took one wrench to remove inlet hose then two wrenches to remove 90 degree brass fitting and another to hold solenoid. I used a nut drive to remove two screws that released the solenoid from the dishwasher frame. I used teflon tape to reattached the 90 degree brass fitting and inlet hose.

On the front ,lower side of sprayer arm removed the 1/4" screw and you have to stick your head inside and look on the backside of the spayed arm. Locate the plastic clip and gently pry a little just enough to loosen it off the rest of the way, be careful not to break off. It came right off I popped on the new one replaced screw and rain a load of dishes. Thanks for your help and great products for us do it yourselfers.

I disconnected the pipes to the inlet valve. I removed the bolts from the bracket holding the valve. I tried to use two wrenches to remove the brass angle pipe thingie off the bottom of the old valve. I then beat on it with a hammer, then I just threw it against the basement floor till it came off. I would recommend getting a new brass angle pipe thingie before you start.

My son took the part and it plop right into place with a click, and we were able to use are dishwasher again,Thanks

I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.

Removed bottom panel unplugged wires removed two screws removed it then replaced it

Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.

It was amazingly easy repair. I just order the correct parts from “PartSelect” and installed them and done. It was fixed.

I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!

very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing

Took lower panel off with screwdriver. Removed old spring. Attached new spring. Very easy, and I'm a woman. LOL

Troubleshot and found that the solenoid had burnt up locking the drain door in closed position. I ordered solenoid, Note: I only received the solenoid. I used the old bracket and springs along with the piston arm for the solenoid. I had to break it free from the old solenoid. Once I got everything cleaned up and put together it took me about 10 minutes to install the solenoid. I manually tested mine prior to wiring back up to ensure proper movement and then tested to ensure that the piston arm did not pop out of the solenoid base.

Pieces just snapped together. Simple an quick. Part select was wonderful in assisting.

Attached is a link to a great youtube video, that shows the exact steps to take to do this job. I just follow the instructions and the repair was flawless.