ADW1100NW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Pembroke Pines, FL
- Parts Used:
- WD16X10011
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Could not get the arm to close.
I could not pull it out to get the new one in so I used a dremmel. Then pressed in the new one.
Thanks for your help.
Thanks for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from La Quinta, CA
- Parts Used:
- WD35X21038
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Rear wheels wouldn't roll, so bottom rack had to be lifted into place. Backbreaking.
The most difficult part was removing the old wheels. The plastic coating on the rack had come off, leaving the metal exposed. The wheels had rusted on - that's why they wouldn't roll. Once we got them off with pliers, hammer, screwdriver and basically everything in the tool chest, we were home free. Installing the new wheels and axles was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- M. from Phoenix, AZ
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
From the three bottom rack wheels on each side, the middle wheels were missing from each side.
I measured the diameter of the working wheels from the existing ones, and located the parts I needed from the website. I order two packages, each containing the wheels and axles for the rack.
When delivered, I snapped the wheels onto the delivered axles. Then, I snapped the axels unto the bottom rack, at the correct place. I used a large pliers for leverage because the axel was a bit tight to just simply snap on.
The middle wheels are located just behind the front wheels, thereby offering support when the botton rack is pulled forward for loading. Likewise, they offer support when the rack is pushed back in place.
When delivered, I snapped the wheels onto the delivered axles. Then, I snapped the axels unto the bottom rack, at the correct place. I used a large pliers for leverage because the axel was a bit tight to just simply snap on.
The middle wheels are located just behind the front wheels, thereby offering support when the botton rack is pulled forward for loading. Likewise, they offer support when the rack is pushed back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from Aurora, CO
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels kept coming off of the basket
Just remove the lower basket from the machine and pull the old wheels off. Then snap on the new wheels on the pegs. The old style wheels snap in place without much force. The new wheels take much more force to install and lock onto the basket which keeps them from coming off when the basket is heavily loaded.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Finksburg, MD
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
GE Dishwasher leaking
Inspected the old gasket. Removed, cleaned, re-seated existing gasket. Tested and found smaller leaks. Purchased and installed new gasket. Majority of leaks stopped but some detergent still leaks. Unsure what the problem is with that but the main leaks have been fixed. Dishwasher is less than 5 years old. Thank You.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Oak Hill, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
4 wheels missing from diswasher rack (lower)
removed the rack and snapped the 4 week/axle assemblies on rack by hand pressure returned rack to track.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelvin from Sun City West, AZ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaks
All new seals
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Arlington, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water leaking out from bottom of Dishwaser
Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Fair Oaks Ranch, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom shelf would not roll properly
so easy! Ordered the rollers and clips ... popped them on and done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from mashpee, MA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom basket of dishwasher kept following out
i needed new rollers and inserts to keep wheels on now its like new when i pull out bottom basket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- R. Cecil from Norfolk, VA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wheel was distorted
Simply replace wheel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Chatham, NJ
- Parts Used:
- WD35X21038
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
wheels colapsed
replaced new wheels
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SCOTT from BOSSIER CITY, LA
- Parts Used:
- WH23X10028
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Pump motor went out and quit draining
My part came in and my husband was at work so..... I did not want to wait for him to come home to wash my clothes! I installed the motor myself and I was not even the one that took it off! It was so easy to do! Turned the washer on and bingo it was back and going! So glad I can get the parts myself and avoid the middle man and his bill!!! Hook up the drain hose with pliers and screw the motor to the frame and that's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Alexandria, VA
- Parts Used:
- WD35X21038, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost wheel
just snapped the new part in. couldn't have been easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nugent P from Garner, NC
- Parts Used:
- WD15X10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
dishes not getting clean, top rack not washing
remove front lower cover, 2 philips screws, turn off water supply under kitchen sink to dish washer, turn off power to dish washer, remove water supply line to valve, remove power to valve, clip ons, remove two 5/16" screws holding valve on, turn valve gently to access clip holding washer supply hose, push clip up hose and hold hose while pulling valve off. re-install in reverse order, a flash light helps.
Was this instruction helpful to you?
Thank you for voting!