PDW9900NB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ellen from DOVER, DE
- Parts Used:
- WD12X10184
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
No video for this new version of the part
The entire flat side of the end cap, (with the cutout latch), goes on the outside of the guide bar. It took less than 15 seconds to insert. It took about 30 minutes of searching for videos and playing around with the part to figure this out. A simple diagram would have been helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carla from valdosta, GA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Food particles had started stopping up spray arm and get them out.
Pulled old spray arm off and snapped new one on. Less than 3 minutes and works great. Dishes are cleaner now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from LAS VEGAS, NV
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hinge arm link wore out
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Norwell, MA
- Parts Used:
- WD24X10045, WD01X10279
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
New install missing drain tube and clamp.
Purchased new $1400 dishwasher from sales floor for $699. Cosmetically perfect, but missing drain tube and clamp. Seemed like a good deal... and it was. Needed parts were $34. Install of this machine was a breeze, and it is suoer quiet...I need to get down on the floor and listen for water flow to know that it's working. Really.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack D from CLEBURNE, TX
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Heat shield on lower spray arm came loose and blocked spray arm from turning
Followed instructions on how-to video on website on how to remove and replace lower spray arm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from TYNGSBORO, MA
- Parts Used:
- WD08X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Started to have a leak
Pull out the old, died gasket. Clean out track that holds gasket. insert new gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- M Anne from VIENNA, VA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Our dishwasher lower arm had become clogged
HAHA! The easiest repair we have ever done! Took it out of the box, snapped the old arm loose, put the new arm in and -- the dishwasher works like new! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from FAIRFIELD, CT
- Parts Used:
- WD28X24469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Holes in old dishwasher basket
The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Chandler, AZ
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Due the the age of this dishwasher (13 years) both upper and lower racks were showing significant rusting.
This lower rack (GE part #WD28X25960) was ready to roll right into the dishwasher straight out of the box, no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sunil from Solon, OH
- Parts Used:
- WD35X21041, WD12X10262, WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheels would keep popping off
The repair is just a couple of minutes job. All I had to do was to pop the wheel axle in the new wheels, remove the old wheels and put the new ones in. The wheel axles on the original one, were like clasps. All one needs to do is to pull the clasp to one side and slide the wheel out. The new one, just needs to be pushed in. In my case, I could have just swapped out the axles, but decided to change the whole set anyway.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juliana from Danville, CA
- Parts Used:
- WD35X21041, WD12X10262
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels on lower rack were partially melted and falling of all the time, so I couldn't pull the rack out, it was annoying!
It was sooo easy, I can't believe I took so long to get these new rollers and studs. Shipment arrived in 2 days, I removed those old melted wheels, through them away and installed the new ones, took me less than 10 minutes, it was painless, no tools needed. I did follow a tip from a buyer that was to attach the studs to the wheels prior attaching them to the lower rack and it was a very usefull tip. Do that! Now my dishwasher is like new again. Great shopping experience, Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lakewood, NJ
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Wheels on lower basket kept falling off, axel worn out.
Removed empty basket from dishwasher. Placed basket upside down and removed remaining wheels from basket by detaching worn axel from attachment points. ie, No tools needed for this procedure. Once axel and wheels were removed, I squeezed the end of the old axel with needle nose pliers or regular pliers to relieve the outward pressure and pushed the old axel out of the wheels. Easy, popped right out.
Positioned new axel against the outer wheeel hole and applied thumb/finger pressure to snap in new axel. Took the wheel with the new axel and
attached it to the basket at the original position. New axel grips the basket like a clothes pin would.
Continued and replaced all eight axels at this time.
Replace basket in machine, stand back and admire work and parts!!!! Parts received promptly with no hassels. Excellent company to do business with, clear photos and ordering forms.
Will definately re order again if needed. Thank You.
Positioned new axel against the outer wheeel hole and applied thumb/finger pressure to snap in new axel. Took the wheel with the new axel and
attached it to the basket at the original position. New axel grips the basket like a clothes pin would.
Continued and replaced all eight axels at this time.
Replace basket in machine, stand back and admire work and parts!!!! Parts received promptly with no hassels. Excellent company to do business with, clear photos and ordering forms.
Will definately re order again if needed. Thank You.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Magnolia, TX
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Basket Wheels Were Falling Off
This was a simple part swap. The stud rollers are the small peg-clips that hold the wheel on the lower dish rack. Removing the old stud rollers from the wheels required a pair of pliers. I then popped the new stud rollers into the old wheels and snapped them back onto the lower dish rack. I scored some major points from my frustrated wife -- easy, fast fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Placentia, CA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Bottom dish basket would not roll in and out. Wheels were falling off.
Removed the existing stud rollers with the wheels attached. Then removed the wheels from the stud roller. Then snapped the wheels on the new "Better Designed" stud rollers. Then easily snapped the new stud roller assembly in place. Piece of cake...works like a charm.
Thanks,
Randy
Thanks,
Randy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Easley, SC
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
wheels kept falling off bottom rack
Man, if you need help doing this repair, you shouldn't even own a dishwasher, much less a house. This was the easiest repair in the entire galaxy. First, I removed the old wheels, which was easy becasue they were always falling off by themselves. I then had to use pliers to squeeze the old studs to remove them from the wheels. All the wheels were still in good shape. Then I snapped the wheels onto the new studs, and snapped the studs onto the lower rack. And then, it was like I was in heaven. Bluebirds were singing, the sun was shining, my lower rack was sliding in and out and in and out like it was new. O happy day.
Was this instruction helpful to you?
Thank you for voting!