F71C765BS0 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pam from Cherokee, AL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a wheel on dish rack
just slid the wheel on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from lees summit, MO
- Parts Used:
- 5304507405, 5303943103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no issues
replacing 2 wheels was a breeze. did not need the screws afterall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Racquel from Lake Charles, LA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing roller made it difficult to move rack.
The new roller just snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danielle from Williamsburg, VA
- Parts Used:
- 5300809611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
leaking out front
The gasket was easy to remove and easy to replace. Our story is interesting because upon calling SEARS to find the replacement part we were told they no longer make it because the dishwasher is too old (approx. 15 years). It works wonderfully so I was annoyed to think we'd have to buy a new one just because of a bad gasket. My husband has a knack for finding things online and eventually discovered your site as well as the original drawing of the machine to find the part number and lo a behold, it fits perfectly. No more leaks! Sweet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from NORTH BEND, OR
- Parts Used:
- 5304507405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced the side rollers in the dishwasher
Removed the old rollers with with screw driver. Used the original screws and washers, and reinstalled the new rollers. Had been having trouble with top dish rack metal slides popping out of the old rollers. I not that the replacement rollers are slightly larger and have slightly deeper groves for the slides. Have not had the new rollers installed long enough to see if they remedied the problem. Will know in a few weeks time. So far, so good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lin from San Francisco, CA
- Parts Used:
- 5300809611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher leak
At first remove the lower rack to give more room for you to lean over the inside of the dishwasher then remove the old gasket tub 90 inches long make sure that you know which side goes where, so that it will be easy to put the new one. Then press the gasket firmly on the side.Now you can start your dishwasher with no leak and saves you a lot of money for buying a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from ERIE, PA
- Parts Used:
- 5300809611
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher was leaking from the front left corner. Gasket seemed bad on that corner by visual and physical inspection. Gasket moved quite a bit on that corner and not on the right side.
The repair was simple. When the part comes, you may need a hairdryer to heat up the plastic a bit to get any kinks that may have happened during packaging or shipping, very easy 5 minutes. Removed the old gasket by hand, very easy, 1 minute. You will need to clean out the track that the gasket sits in. Mine had years of black gunk inside of it. You will need qtips or a small screwdriver with some tissues or papertowels, easy but took 15 minutes to clean out properly. Installed new gasket in the track, start at the top middle, there is a notch on the gasket so you know where the middle is. Installed by hand, just push bottom edge into the clean track, easy 5 minutes. Ran the dishwasher with no leaks. Very pleased with the result and how easy the gasket was to remove and install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from staten island, NY
- Parts Used:
- 5304507405, 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher racks would come off track
I clipped the wheels onto the rack. It couldn't be any easier. then i removed the # 25 torx screw which attached the broken slide wheel to the tub and installed the new wheel with the same torx screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSVILLE, NJ
- Parts Used:
- 5304532229
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing part
Just pushed it onto the rod that held the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Longview, WA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken clip would no longer secure wheel
Snapped the new one in. One second repair - like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAWINDER from HOUSTON, TX
- Parts Used:
- 5300809611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Water leak
Replaced the gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Upperco, MD
- Parts Used:
- 154106202
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Small Constant Drip (Leak)
I pulled out the dishwasher removed the two heating element insulated wires and removed both threaded brass nuts and replaced them both. Problem solved. Luckily I have a local parts and repair store with a repairman that knows every part of every appliance ever made (no kidding, I have yet to stump him with a part or question). He did not have the parts, told me to go to partselect.com order two nuts, replace them both at the same time, and fix it myself because its an easy repair and not worth paying hundreds of dollars, if you can use a wrench. He was right, and partselect.com had the right parts, at the right price, easy to find and order, and I can impress the wife with my repair skills. Thanks again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Los Angeles, CA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack got hung up & wouldn't roll
I snapped on the new roller and bingo! problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Charlotte, NC
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heating Element Seal and Nut
Never worked on a dishwasher before but quickly learned that on this particular one, it's only this thin little brass nut that tightens down the element from the underside of the washer. If not tight enough, water drips right down onto the electrical connections. In this case water began to drip and the heat from the electrical current began melting a clear rubber shield thing. Luckily I was home during the cycle and figured out the problem. Great website that seems to have all necessary parts for my washer. Quick shipment!
Was this instruction helpful to you?
Thank you for voting!