FDR252RBB2 Frigidaire Dishwasher - Instructions

I opened the control knob panel. The latch assembly is located behind inside the panel along w/ the wires. This is my second replacement of the assembly. The last one lasted about 2 years. They should make a sturdier latch assembly next time.

Important - turned the power to the dishwasher off. took the screws out of the top part of the back door panel. pulled the wire leads of the broken switch, replaced the switch with the new one, reconnected the wires, put the panel back on.
Fixed

removed screws to loosen front door panel then removed the wire connection, then removed the broken latch with screwdriver, installed new latch in same manner, fastened front panel back with the removed screws and I was back in business, easy as pie.

First I removed the 5 screws holding the dishwasher door control panel. Then removed the 2 screws holding the broken latch. Then removed an electrical contact from the broken latch and installed to the new latch one contact at a time. Reassembled all in reverse order to completion.

Removed six philip head screws to remove upper half of the dishwasher door unit to access handle, then remove handle by remove two star screws and for wires connectors. Installed in reverse.

Note:
I was very impressed on how quick I received the part after it was ordered.

The repair was pretty straightforward. If somebody is attempting, they should make sure that screws close the bottom part of the door should be opened. You only need to open the top 4 screws.

Removed the rack out of dishwasher. Removed sprayer by removing 4 screws. Removed cover to pump propeller assy.by just lifting up on the cover. Then you remove 4 screws from the pump cover. Remove the propeller. Pull up on shaft and seal. Then when you replace everything just reverse the directions.

Simple- Disconnect electric to washer, Remove inner door panel with philips screw driver, disconnect electrical wires watching exactly how they are to be replaced. remove star screws securing handle mechanism. Replace with new handle, connect wiring, replace inner door panel and your all set. Good luck.

I clipped the wheels onto the rack. It couldn't be any easier. then i removed the # 25 torx screw which attached the broken slide wheel to the tub and installed the new wheel with the same torx screw.

First i removed the screws on the back panel, unscrewed the latch, removed the wires and installed the new latch.
I found the latch is too expensive for a little plastic part.

Removed the screws that hold the panel on ( just the top ones-no need to go all the way down the sides. Need a "star" headed screwdriver to remove the switch itself. Then removed the wires (4),one be one, so as not to mix them up. reinstalled all thescres for the switch, then the panel. Job done.
What amazes me is that Frigidaire doesn't read your page to realize that the handle assembly was defective and send out a recall. look at all the repars listed in your site , and these re just from the people that have responded with comments and who use your service. New handle/switch is much more sturdy with a higher density plastic that the original. Your service is easy to use, prompt and accurate. Fixed the dishwasher while my wife went to the store. Dishwasher done in 15 minutes and watched theNCCA tournament for 2hours in complete peace !!!!! No need to tell the wife only spent 15 minutes.

I replaced the old cap with the one I ordered from this site

Removed the screws that held the cover on, then removed the 2 screws that held the door latch in place. Disconnected the broken door latch and attached the new one. Put all the screws back in and that was it! Also, the shipment of the part was SO QUICK!

Removed the front cover by unscrewing the 8 screws. Removed the latch and attached new one. Re-attached front cover, and it works fine.
The gasket was in fine shape, and I question why I had to purchase the gasket in order to get the latch. Seems crazy and an unecessary expense on my part.

First, I located the dishwasher switch in the circuit breaker and turned it off, so as to kill power to the dishwasher - DO NOT PROCEED WITHOUT DOING THIS FIRST. Unscrewed front panel by removing 6 screws on the inside of the door frame. Then pulled 2 white wires on left and 2 black wires on right off of bottom of latch. Then used hex wrench to remove 2 hex screws holding handle and latch to frame. Then reassembled in reverse order as I disassembled. Note that there was a video on the site when I ordered the part, and it demonstrated all the steps; however, when I received the part and went back to the site to review the video again, it was gone. I'm glad I paid close attention the first time I watched it as it was extremely helpful and showed me exactly how to complete the installation.