FDR252RBB2 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Seth from Seattle, WA
- Parts Used:
- 154219201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Dishwasher was leaking water
The spray arm had become damaged on one side -- one side had apparently melted off. I replaced it, and it seems to have fixed the problem for now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Prior Lake, MN
- Parts Used:
- 154219201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Lower repair arm failed and did not allow dishwasher to complete wash cycle. Repair completed in less than 10 minutes and dishwasher is now functional. Thanks.
remove center nut retaining the arm to the unit and replaced the arm.
replaced the nut.
complete.
replaced the nut.
complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanette from Fort Lauderdale, FL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed wheels for the roller part of dishwasher
Just snapped the wheels on and attached the bracket to the existing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Giovanni from Glen Burnie, MD
- Parts Used:
- 5304442175
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Latch Broke Off, Can't Close Door
Very easy to remove old broken door latch assembly, easier to install replacement. With door fully opened, I removed the 8 screws holding down the whole front casing, including the controls casing. Removed 2 Torx screws holding door latch assembly and then made sure that I marked all 4 wires before disconnecting them from door latch assembly. Connected wires to new door latch assembly, secured it with the 2 Torx screws, aligned and secured the controls and front cover casings with 8 screws. Done within 30 mins. Thanks guys for posting how-tos and thanks to PartSelect for a very fast shipping!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from lees summit, MO
- Parts Used:
- 5304507405, 5303943103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no issues
replacing 2 wheels was a breeze. did not need the screws afterall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- erika from deerfield beach, FL
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
latch broke had to open door with a screwdriver
removed screws to loosen front door panel then removed the wire connection, then removed the broken latch with screwdriver, installed new latch in same manner, fastened front panel back with the removed screws and I was back in business, easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Whitman, MA
- Parts Used:
- 154574401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
detergent door/dispenser would not close,
removed screws holding door panel, turned off electricity,removed old part and installed new dispenser, the dishwasher is back in business. Be sure to use the proper screws when putting back the door panel.The instructions for installation were in the new part assembly.
Thank You for all your help
Pat Johnson
Thank You for all your help
Pat Johnson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from BRANDON, FL
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Handle was cracked and missing half of it
First, I located the dishwasher switch in the circuit breaker and turned it off, so as to kill power to the dishwasher - DO NOT PROCEED WITHOUT DOING THIS FIRST. Unscrewed front panel by removing 6 screws on the inside of the door frame. Then pulled 2 white wires on left and 2 black wires on right off of bottom of latch. Then used hex wrench to remove 2 hex screws holding handle and latch to frame. Then reassembled in reverse order as I disassembled. Note that there was a video on the site when I ordered the part, and it demonstrated all the steps; however, when I received the part and went back to the site to review the video again, it was gone. I'm glad I paid close attention the first time I watched it as it was extremely helpful and showed me exactly how to complete the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- linda from pittsburgh, PA
- Parts Used:
- 154574401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
My soap dispenser had worn out and wouldn't stay closed anymore
Received the part quickly and installed it with no problem whatsoever. Have order parts from PartSelect before and have been very happy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Houston, TX
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door latch broke
First I removed the control panel and then removed the screw holding the handle. I then pulled the connector wires off and onto the new handle. I then screwed the new panel into place. Easy job, no mess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from MILFORD, MA
- Parts Used:
- 154574401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door broken would not close
1.Turn off electricity. 2. Remove two Phillips screws on either side of front panel 3. Remove front panel 4. Remove 6 screws from the old dispenser 5. Pull both wires connectors from dispenser 6. Remove dispenser 7. Install the new dispenser and reverse the steps
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Niall from Schaumburg, IL
- Parts Used:
- 154574401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not stay closed
Followed the YouTube video. Replacement fit perfectly , only took 10 minutes to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from NORTH BEND, OR
- Parts Used:
- 5304507405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced the side rollers in the dishwasher
Removed the old rollers with with screw driver. Used the original screws and washers, and reinstalled the new rollers. Had been having trouble with top dish rack metal slides popping out of the old rollers. I not that the replacement rollers are slightly larger and have slightly deeper groves for the slides. Have not had the new rollers installed long enough to see if they remedied the problem. Will know in a few weeks time. So far, so good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from GREENFIELD, IN
- Parts Used:
- 154388801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Unable to add rinse aid
Screwed in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSVILLE, NJ
- Parts Used:
- 5304532229
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing part
Just pushed it onto the rod that held the old one
Was this instruction helpful to you?
Thank you for voting!