GDPH4525AF0A Frigidaire Dishwasher - Instructions

The hose goes from the water inlet solinoid to the side of the dishwasher.Remove the kick plate from the bottom front of the dishwasher. Disconnect the water supply to the inlet of the solinoid valve (copper tubing on mine). Remove the screws under the counter top which hold the dishwasher in place. slide the dishwasher out from under the cabinet only as far as needed to expose the hose(about 1 foot). The hose is behind the insulation. Remove the hose clamps from both ends of the hose(solinoid outlet and side of dishwasher)Remove hose carefully because this is all plastic. Install replacement hose and clamps. The new hose is several inches too short and will not fit into the upper hose guide, just bend it underneath. Be sure to put hose in lower keeper on side of dishwasher. Attach clamps, tape insulation back in place, slide dishwasher back under counter and install screws under counter. Attach copper tubing to water inlet solinoid valve. Run dishwasher and check for leaks. Replace kick plate. Note: I had enough loose electrical wire to slide my dishwasher out. If you don't have enough wire to slide out the dishwasher you should call a repair man.

Remove old gasket from tub, soak new gasket in hot water for a few minutes then install starting from center top of tub, when done installing close door for 24 hours, then try to see if leak fixed.

Ditto the other comments. Easy, great savings. Perfect. Thank you!

very simply removed 2 clamps, replace hose, re-installed clamps

Wrap your pliers in some kind of padding so you don't damage the plastic. Spin the base ( not the spinner itself) which is left-threaded(normal). If the gasket doesn't fall out (mine did) pull it out gently. Clean the gasket socket with a rough cloth or scotch-brite pad and install the new one. Put it all back together and wash dishes, man.

replaced gasket easy-peesy

After reading some "Suggested Installation Instructions" on the Parts Select Website, I felt at ease tackling this job. After opening the door, I simply pulled-out the existing door gasket. The installation involved simply pressing in the new gasket with my finger and insuring it was properly seated. The only tool I had to use was a pair of scissors to cut the excess length as I pressed it in. REALLY APPRECIATED THE SIMPLE INSTALLATION INSTRUCTIONS as I had never done this particular task.

I just pulled the old one out and installed the new.

Pulled out the gasket,trimmed the gasket to fit and alittle pressure to put.it in place, very easyto do. No worries any one can do this and savek yourself costly repair person.

Very helpful and was amazed how quickly it was delivered. Very pleased.

I woke up on Christmas Day to water pooling under the kitchen sink (I guess I made the naughty list last year). Upon inspection, I could see that the water connections for the faucet were damp. Since I had all the parts, I replaced the faucet and service lines. Once complete, there were no leaks so I turned on the dishwasher to double check for leaks in those lines. It was all dry when the dishwasher finished but the next morning, more water under the sink.
I proceeded to replace the water line to the dishwasher and ran it through another wash cycle. Still leaking.
I found PartsSelect online and order a new drain line for the dishwasher. To my amazement, FedEx dropped off my order the next morning........yes, the next morning.
It took five minutes to remove the old drain line and install the new one (just a worm clamp at each end). It would have been faster than that but I don't get up and down as fast as I use to.

on close investigation the problem was not the element ,but one of the brass nuts was fractured this was repaired and leakage was rectified. I .would add that your service and delivery was excellant and the unrequired element will be returned to you thanks

Removed old gasket,placed new one on pressing into place.Very quick and easy.Saw the youtube on how to do it.Unfortunately this was not the problem.now have a new dishwasher same brand.

Spotted the source of the leak at the first heating element under the dishwasher. Removed the brass mounting nut and it was cracked. Replaced with new part from PartSelect.com and the leak was fixed. Apparently the heating element gets so hot it tends to crack the mounting nuts, which results in a leak. Delivery time for part said 3-5 days - mine arrived one day after ordered!

Purchased new drain pump thinking that was the issue. When I was installing I noticed the drain hose was clogged. Since the way out cabinets were installed by the previous owner getting the dishwasher out is a little more complex so installed the drain pump and drain hose just to make sure. Runs like new!