605222851B Frigidaire Dishwasher - Instructions

Followed the on-line tutorial. BINGO!!!!

Opened the package and inspected the new spring
Went to Part Select site to read directions
shut off the power
Reached under the dishwasher and disconnected the old spring from the frame
detached the old spring from the pulley cord
attached the new spring to the pulley cord
reached under the dishwasher and attached the new spring to the frame
Turned the power back on
total time around 15 minutes including reading the instructions
Piece of cake!

Instead of moving the unit out from under the counter, I did the job with the unit in place: (1) long reach to remove the old springs and attach the new ones to the frame at back of the unit, (2) use a loop of string to hook onto the other end of the spring, stretch it a little, and keep it stretched by hooking the other end of the loop to the screw that adjusts the unit's height, (3) slip the end of the cable to the front end of the spring and check to make sure that the cable is on its pulley, (4) take the string off the adjusting screw and wiggle it to free it from the end of the spring. (For comfort, lie down on a yoga mat when you do this job - thanks to my wife for this helpful suggestion!)

open door pull out old rack replace with new rack !

open door rolled it and place the new

Watched installation video and followed directions. All went smoothly.

Opened door. Located 2 Phillips head screw s attaching the dishwasher to counter and removed them. Slid the dishwasher out about 8 inches. Love broken cable and removed . Inspect spring and attached new cable. Inspected opposite cable and spring. Tucked insulation around dishwasher and slid back into place. Reattached 2 Phillip screws and closed door.

Remover the cracked heating element with the new heating element.

I followed the steps on YouTube.

NOTE: I am a complete amateur, and had NEVER attempted to work on my own appliances before this. Diagnosis via web search determined that the drain pump was the most likely problem. PartSelect.com had the best prices and, as it turned out, the fastest delivery. I shut off the power to the dishwasher at the circuit breaker and turned off the water supply under the kitchen sink. I took all of the removable parts out of the dishwasher (lower rack, spray arm, strainer), and using a shop-vac, I emptied the water that had pooled at the bottom of the dishwasher. I removed the kickplate (2 screws) to disconnect the water line (pliers) and the drain hose clamp (flat screwdriver). Both of these had some water in them, so I used one of a few shop towels that I had handy to keep things dry. Opening the dishwasher gave me access to the screws that anchor the unit to the countertop, which I removed (phillips screwdriver). Loosening the adjustable feet and gently rocking the dishwasher dislodged it to the point where I could remove it, but not before laying cardboard down to protect the kitchen floor. Once removed, I flipped the unit over and disconnected the old drain pump's electrical leads, noting which one went where. Three star-shaped screws held the drain pump in place - one of which was difficult to get to, due to the size of my driver and the location of the main motor. I removed/replaced the pump, connected the electrical leads, flipped the dishwasher upright, and slid it back under the countertop. I re-extended the adjustable feet and made sure everything was level front-to-back and side-to-side before securing the two screws through the tabs into the countertop. Under the unit, I reconnected the water line, turned the supply back on, and checked for leaks. I reconnected the drain hose and then turned the power back on at the circuit breaker. I did a quick test run of the unit and not only did it drain properly, but there were no visible leaks. I will reinstall the kickplate in a week or so, after I can run a couple loads of dishes and ensure that there are no issues under the unit. With a small amount of web searching, some great help from the PartSelect crew, and a bit of fortitude, I saved hundreds of dollars and have a far better understanding of how my dishwasher works. That's a win-win in my book!!

Checked your videos and found the lower spray arm damaged (nubs worn down). Previous owner had some work done and didn't reinstall the parts properly. While during the repair, I also decided to replace the Detergent Dispenser and make a new spray shield. I guess the previous owner decided one wasn't needed.

Easy install, no noise.

Capt. Hank

I pulled out the dishwasher and found the inlet tubing had a tear in the accordion part of the tube. I searched online for the model number and was directed to PartSelect. I ordered the inlet tubing, and it only took a few days to get to me. I then watched the video and was able to install the new tubing.

PartSelect is a life saver and I saved lots of money by not having to call a repairman.

Took the old one out, put the new one in! Soooooo hard. Lol

Never worked on a dishwasher before but quickly learned that on this particular one, it's only this thin little brass nut that tightens down the element from the underside of the washer. If not tight enough, water drips right down onto the electrical connections. In this case water began to drip and the heat from the electrical current began melting a clear rubber shield thing. Luckily I was home during the cycle and figured out the problem. Great website that seems to have all necessary parts for my washer. Quick shipment!

Snapped new wheels into place on the axel. New wheels were exactly like the old ones