FDPC4314AB0A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Kirkwood, MO
- Parts Used:
- 807117001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water Leak in Dishwasher Drain Line
I woke up on Christmas Day to water pooling under the kitchen sink (I guess I made the naughty list last year). Upon inspection, I could see that the water connections for the faucet were damp. Since I had all the parts, I replaced the faucet and service lines. Once complete, there were no leaks so I turned on the dishwasher to double check for leaks in those lines. It was all dry when the dishwasher finished but the next morning, more water under the sink.
I proceeded to replace the water line to the dishwasher and ran it through another wash cycle. Still leaking.
I found PartsSelect online and order a new drain line for the dishwasher. To my amazement, FedEx dropped off my order the next morning........yes, the next morning.
It took five minutes to remove the old drain line and install the new one (just a worm clamp at each end). It would have been faster than that but I don't get up and down as fast as I use to.
I proceeded to replace the water line to the dishwasher and ran it through another wash cycle. Still leaking.
I found PartsSelect online and order a new drain line for the dishwasher. To my amazement, FedEx dropped off my order the next morning........yes, the next morning.
It took five minutes to remove the old drain line and install the new one (just a worm clamp at each end). It would have been faster than that but I don't get up and down as fast as I use to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Apopka, FL
- Parts Used:
- 154430501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher door was falling heavily down when pulled open because one of the two springs was broken
identified the correct part to order. when it came, I used a Phillips-head screwdriver to undo the two brackets that hold the unit into the bottom of the countertop so I could slide it out a few inches. once I determined which spring was broken, I pulled out the remaining part and replaced it with the new one -- hooking it first into the hold farthest back in the appliance and looping the longer end over the top of the swiveling catch device that holds the front of the spring. then pushed unit back under countertop and screwed two brackets back into place with the existing wood screws and screwdriver. piece o' cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from punta gorda, FL
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
thought water leak via heater element
on close investigation the problem was not the element ,but one of the brass nuts was fractured this was repaired and leakage was rectified. I .would add that your service and delivery was excellant and the unrequired element will be returned to you thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from Salisbury, NC
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
(leaking) heater element nuts cracked under dishwasher
power off, take off kickplate, unplug 2 wires and unscrew broken nuts, put new nuts on, plug wires back in,(run dishwasher one cycle to make sure no leaks) put kickplate back on, power on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Camarillo, CA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dish rack difficult to pull out to load/unload
Thanks to PartsSelect exploded drawings, it was easy to identify and order the part. Installing was a case of just snapping it on the rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BOB from MERRIMAC, WI
- Parts Used:
- 5304523457
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
leaking water inlet
removed old hose by loosening clamps replaced hose reclamped
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilburn from Cumming, GA
- Parts Used:
- 807117001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
need drain house
Very helpful and was amazed how quickly it was delivered. Very pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roseana from Virginia Beach, VA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The close door code kept going off and was leaking on the bottom.
Took the gasket off and put the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Houston, TX
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost several wheels from lower rack of dischwasher
Nothing to it. Just inserted the iron stud into the center wheel and pressed the bracket onto the stud.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauren from Marietta, OH
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher leaking
Removed old gasket,placed new one on pressing into place.Very quick and easy.Saw the youtube on how to do it.Unfortunately this was not the problem.now have a new dishwasher same brand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Meansville, GA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Dishwasher leaking from underneath unit
Spotted the source of the leak at the first heating element under the dishwasher. Removed the brass mounting nut and it was cracked. Replaced with new part from PartSelect.com and the leak was fixed. Apparently the heating element gets so hot it tends to crack the mounting nuts, which results in a leak. Delivery time for part said 3-5 days - mine arrived one day after ordered!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Berlin, NY
- Parts Used:
- 154430501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
broken spring on door
replacing spring is easy.but you have to disconect the water line to slide the washer out to get at the spring.service was exelant. part was deliverd next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Tiverton, RI
- Parts Used:
- 5304507087
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench (Adjustable), Wrench set
leaking feeder tube
The repair went well,however I must comment on parts select. I do most of my work on the net, I have never had a company fill an order and ship the part so quickly I was amazed I had the part 3 days after I placed the order. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Isabella from Santa Fe, NM
- Parts Used:
- 154430501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Door spring was not efficient
The new spring I installed according to the video. It had a smaller diameter than the original so did not work well but when I left the old springs on the door and added the new ones so now I have two springs on each side I had a great improvement. Now the door does not fall open and hit me in the shins. If the replacement spring had the same diameter and therefore the same strength as the original that would have been even better
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Manitowoc, WI
- Parts Used:
- 154430501
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Broken door spring.
After watching the video the replacement went very easy. The only thing I would suggest is that you replace both springs to equalize the tension.
Was this instruction helpful to you?
Thank you for voting!