FDPC4314AB0A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kathy from Greer, SC
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower rack rollers were missing
Rollers just snapped on the diswasher rack. Took just seconds to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aleksandr from West Palm Beach, FL
- Parts Used:
- 5304532207
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
was brocken
just replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- willis w from broomes island, MD
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Leaking
All I have to say is paets select is the best company I have delt with in the last 20 years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mahlon from Kirby, TX
- Parts Used:
- 807117001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rat chewed thru the drain HO9SE
pULLED THE WASHER FROM THE COUNTER disconjnected the house from the garbage disposal connected thenew hose to the disposal, remove other end of old hose from thedishwasher and replace with the new drainage hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Isabella from Santa Fe, NM
- Parts Used:
- 154430501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Door spring was not efficient
The new spring I installed according to the video. It had a smaller diameter than the original so did not work well but when I left the old springs on the door and added the new ones so now I have two springs on each side I had a great improvement. Now the door does not fall open and hit me in the shins. If the replacement spring had the same diameter and therefore the same strength as the original that would have been even better
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Oak Harbor, WA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Brass Nut Cracked - Water Leaks O Floor
I removed the 2 screws that hold the dishwasher in place. Slide out the unit just far enough to access the brass nuts on the heating element. Pulled off the wire, and replaced the broken nut with the new nut. Replaced the wire, slide the unit back into place and reattached the 2 under counter screws. Done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Wauwatosa, WI
- Parts Used:
- 807117001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Had to replace the drain hose (that I screwed up)
I already had the dishwasher removed for remodeling. I wrecked the drain hose myself. When I received the replacement it was a breeze to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from Patchogue, NY
- Parts Used:
- 5304523457
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Water inlet hose replacement
The hose goes from the water inlet solinoid to the side of the dishwasher.Remove the kick plate from the bottom front of the dishwasher. Disconnect the water supply to the inlet of the solinoid valve (copper tubing on mine). Remove the screws under the counter top which hold the dishwasher in place. slide the dishwasher out from under the cabinet only as far as needed to expose the hose(about 1 foot). The hose is behind the insulation. Remove the hose clamps from both ends of the hose(solinoid outlet and side of dishwasher)Remove hose carefully because this is all plastic. Install replacement hose and clamps. The new hose is several inches too short and will not fit into the upper hose guide, just bend it underneath. Be sure to put hose in lower keeper on side of dishwasher. Attach clamps, tape insulation back in place, slide dishwasher back under counter and install screws under counter. Attach copper tubing to water inlet solinoid valve. Run dishwasher and check for leaks. Replace kick plate. Note: I had enough loose electrical wire to slide my dishwasher out. If you don't have enough wire to slide out the dishwasher you should call a repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from South Park, PA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
original rack wheels where bent and upper wheels had melted
husband replaced wheels.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from Salisbury, NC
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
(leaking) heater element nuts cracked under dishwasher
power off, take off kickplate, unplug 2 wires and unscrew broken nuts, put new nuts on, plug wires back in,(run dishwasher one cycle to make sure no leaks) put kickplate back on, power on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Camarillo, CA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dish rack difficult to pull out to load/unload
Thanks to PartsSelect exploded drawings, it was easy to identify and order the part. Installing was a case of just snapping it on the rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BOB from MERRIMAC, WI
- Parts Used:
- 5304523457
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
leaking water inlet
removed old hose by loosening clamps replaced hose reclamped
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilburn from Cumming, GA
- Parts Used:
- 807117001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
need drain house
Very helpful and was amazed how quickly it was delivered. Very pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Rougemont, NC
- Parts Used:
- 154406401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Spinner fell off of delivery tube.
Wrap your pliers in some kind of padding so you don't damage the plastic. Spin the base ( not the spinner itself) which is left-threaded(normal). If the gasket doesn't fall out (mine did) pull it out gently. Clean the gasket socket with a rough cloth or scotch-brite pad and install the new one. Put it all back together and wash dishes, man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cody from kalispell, MT
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
leaking aroung the door
replaced gasket easy-peesy
Was this instruction helpful to you?
Thank you for voting!