FFCD2418US4A Frigidaire Dishwasher - Instructions

There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.

used pliers to hook up spring according to repair video.5 mins to check for proper tension.

I rolled the lower basket out of the way, lifted the spray arm up and out. Then I located the replacement part on Frigidaire's website and placed the order. The part came quickly and I snapped it into place. No tools required. Now my wife is happy and so am I.

Just take the door apart remove the latch

I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!

Greg

Had to shut electricity off and turn water off and disconnect them both. Take the screws out from underneath the counter. Slide out the unit disconnect the filler tube in the back disconnect the hose and replace and repeat the process to put it back together.

Eventually broke off old heating element to get it out

The part wasn't correct and I have to pay postage back which is nearly as much as the part so it's stupid for me to spend more money on a part that want work I want order from your store again.

It took me about 30 minutes to do the repair - took my time and could’ve done it much faster.

The first sensible thing to do is to find the circuit breaker for your dishwasher and switch it off so as not to short anything (or yourself) out. Next, remove the lower piece of metal bracket from beneath the door by unfastening the two sheet metal screws (a nut driver or a screwdriver will do the job), taking note as to how it comes off so as to facilitate replacement. Some will recommend loosening the screws at the top from beneath the counter and pulling the machine forward a bit to gain access to the sides but, if you have a small enough hand (as I do), you can just reach in there and and hook the spring into place. I didn't want to risk loosening any plumbing! You'll need a flashlight to see where the ends connect. And, if one spring is still intact, you can reference that to reassure yourself you've got it right. I was able to stretch the spring out by hand and hook the thing to that little plastic gadget that pivots when you open the door. That's it! Button her up! You're done!

First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.

Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.

This was great! Removed 3 screws, took out old broken part, set in new part and screwed tight! 1 2 3 and done. Very Fast shipping less than 24 hrs.. WIFE IS HAPPY. Ted W.

I removed the three screws that held the stem assembly in place, removed the old stem assembly and replaced it with the new one. Replaced the screws and began using the dishwasher again.

It was a snap. Just pulled the spray arm out, un-snapped it from its holder, snapped the new one in and inserted it back into the dishwasher. Saved $$$ doing it myself.