FFID2426TS5A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ELIZABETH from ROANOKE, VA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original part was damaged and dishes weren't clean
Removed 3 screws, swapped parts - done. Wonderful feeling and saved a service call. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanette from Fort Lauderdale, FL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed wheels for the roller part of dishwasher
Just snapped the wheels on and attached the bracket to the existing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Alamogordo, NM
- Parts Used:
- 140229954072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Top rack had rusted
Slid the rack out, removed the end pieces holding top rack in the sliding arms. Removed the spray arm. It was stiff & a bit hard to get off, but with a little careful prying it came off. Put that spray arm assembly back onto the new rack, slid the new rack back in place, put the end pieces back on and in less than 15 minutes, we were done. Part came in very quickly, I might add. I feel like I have a brand new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from hull, MA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Spray Arm Did not Turn
The bottom spray arm would not turn or fall off the stem assembly, so the dishes would not come clean like usual. The spray arm connects to the stem assembly via two plastic prongs that secure the spray arm. I removed the spray arm from the socket (no tool required) and observed the prongs had worn completely away. I grabbed the power screw driver and removed the assembly (3 screws). I placed the new assembly in place, secured the screws, and attached the spray arm. Finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from FT LAUDERDALE, FL
- Parts Used:
- 5304500204
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water leak
watched a video, really easy fix. Solved the problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from Cherokee, AL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a wheel on dish rack
just slid the wheel on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Racquel from Lake Charles, LA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing roller made it difficult to move rack.
The new roller just snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from FAIRPORT, NY
- Parts Used:
- 5304507158
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The spray arm on the lower level had broken
Easy repair .part was perfect. Did have to you tube video to make sure I was doing it correctly. Instructions with part would be helpful.Part arrived quickly without issue!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from VERO BEACH, FL
- Parts Used:
- 5304533200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rack was rusting on the bottom due to the plastic no longer covering the metal
simply removed the old slide out rack and replace with new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from HAMPTON, NH
- Parts Used:
- 5304506916
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Two of the tub wheels cracked and broke off.
Unscrewed the old ones, new ones come with screw built in and recrewed the new ones in. So easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Sublimity, OR
- Parts Used:
- 154756401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Cable was broke
Opened door. Located 2 Phillips head screw s attaching the dishwasher to counter and removed them. Slid the dishwasher out about 8 inches. Love broken cable and removed . Inspect spring and attached new cable. Inspected opposite cable and spring. Tucked insulation around dishwasher and slid back into place. Reattached 2 Phillip screws and closed door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from WOODBURY, MN
- Parts Used:
- 154827601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old gasket melted.
Watched installation video and followed directions. All went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul J from LEXINGTON, MA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One door spring was broken - the other was spring.
Instead of moving the unit out from under the counter, I did the job with the unit in place: (1) long reach to remove the old springs and attach the new ones to the frame at back of the unit, (2) use a loop of string to hook onto the other end of the spring, stretch it a little, and keep it stretched by hooking the other end of the loop to the screw that adjusts the unit's height, (3) slip the end of the cable to the front end of the spring and check to make sure that the cable is on its pulley, (4) take the string off the adjusting screw and wiggle it to free it from the end of the spring. (For comfort, lie down on a yoga mat when you do this job - thanks to my wife for this helpful suggestion!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert W from OSSINEKE, MI
- Parts Used:
- 5304533200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rack assembly was rusted or rotted out
Took the old rack out and placed the new one in. Easy peasy!
Was this instruction helpful to you?
Thank you for voting!