FFCD2413UB2A Frigidaire Dishwasher - Instructions

The part wasn't correct and I have to pay postage back which is nearly as much as the part so it's stupid for me to spend more money on a part that want work I want order from your store again.

There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.

Isolated the leak and found the nut had split thereby allowing a loose seal and water penetration. Ordered 2 nuts just in case the other goes and the installation was easy. Unplug the unit, remove baseplate, remove screws under the countertop, and slide the unit out a bit. Use needlenode pliers to remove terminal connection and replaced nut. Reverse it for assembly. 3 minutes tops $6 later it is done. Easy money saved by a DIY.

Just take the door apart remove the latch

I watched the video on the website on how to remove the top rack, and installed the new wheel and bushing. Simplest fix I ever did.

I rolled the lower basket out of the way, lifted the spray arm up and out. Then I located the replacement part on Frigidaire's website and placed the order. The part came quickly and I snapped it into place. No tools required. Now my wife is happy and so am I.

used pliers to hook up spring according to repair video.5 mins to check for proper tension.

Found the base was not snapped in. Fixed that by simply pushing down on it and turning until it snapped in place. Ordered a new spray arm when it came in just snapped in literally took less than a minute. Fixed for less than $30 Can't imagine what a repairman would have charged.

Looseing up rack wheeles took out keepers slid in new rack put in keepers and tighten wheel nuts make sure there tight thats it easy a baby can do it.

I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!

Greg

Replaced part

Thought the problem was a faulty door gasket (there was a gap in the middle of it) so I ordered new(new one had a gap also) replaced it anyway - maybe it was worn out? Still leaked! Had to sit and stare at it and cycle it through. finally realized the spray arm had a hole in the end that was spraying directly into the gap in the door gasket. Hot glued the hole and it stopped so I bought a new spray arm - no leaky!

Customer Service Rep by day, Super Mom by night. I literally have 5 minutes when I get home before I have to take my son to football. I was not only able to use the bathroom but repair my dishwasher in that amount of time. It couldn't have been easier, opening the package took longer. Note: replacement arm looked slightly different than the original. All you had to do was to spread the side clips and snap into place. I had my dishwasher running as I was running out the door. Now I bet if I had a service person come to fix it, it would have cost me!

Replaced two springs

I first removed the bottom rack and took out the spray arm (which was now in two pieces) I took some steel wool and scrubbed off the melted residue from the old arm. I took the new spray arm out of the plastic and clipped it into the bottom of the dishwasher. It spun around great and so I put the bottom rack back in and told my wife to try to run a load of dishes throu. It ran great, dishes got clean...easy fx!