FGIP2468UF0A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pam from Cherokee, AL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a wheel on dish rack
just slid the wheel on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Bonaire, GA
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper Spray Arm kept falling off.
The new arm came preassembled. I unscrewed the old arm base with my hand and screwed the new arm in place. The whole process took less than a minute. The new part was not made the same way. It was better than the original. Must have been a problem from the manufacturer. WORKS GREAT!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanette from Fort Lauderdale, FL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed wheels for the roller part of dishwasher
Just snapped the wheels on and attached the bracket to the existing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Brandon, SD
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper spray arm kept falling off
This part fixed problem. The original part seemed to have a defect. Was simple to fix, simply took off old piece still connected and hand tighten the new piece on, it took about 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from Rio Linda, CA
- Parts Used:
- 5304506516, 5304506510
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper Spray arm fell off
The Upper Spray Arm is all one piece....so that was nice. You dont have to order all three pieces, like it shows in the diagram. Very easy to order and install parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Euless, TX
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Spray arm broke off
Very simple repair - in my case part of the upper spray arm broke off, leaving the threaded portion still in the dishwasher. Just unscrewed the remaining broken part, and screwed back in the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Clinton, OH
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking tub seal
Just pulled the old gasket out and popped in the new. I did trim it too shrt however so be careful not to do that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSVILLE, NJ
- Parts Used:
- 5304532229
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing part
Just pushed it onto the rod that held the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from WOODBURY, MN
- Parts Used:
- 154827601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old gasket melted.
Watched installation video and followed directions. All went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Collierville, TN
- Parts Used:
- 5304500204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom seal on door came out and melted on heating element.
Took me about 2 minutes to repair, no tools to repair, very easy installation repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Massapequa Park, NY
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The part would constantly fall after every dishwasher run
Removed the old spray arm by unscrewing it from the top inside of the dishwasher. Then screwed on the new spray arm. Could not have been any easier and it has not fallen off since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Monroe, GA
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper arm fell off frequently
Unscrewed the mounting nut and the assembly came off . A simple task of taking the new assembly and screwing it back on .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from PATTON, MO
- Parts Used:
- 5304506516
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Spray arm fell off during cycle
Unscrew old one and put new one in. Only issue we had was the new nut that screws the arm into place did not fit our machine. We had to take the old one off and use it instead.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Farrell from NEDERLAND, TX
- Parts Used:
- 5304506516
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Upper Spray arm would fall off during the wash cycle
The spray arm is attached to a part that is screwed on. The new part came completely assembled. I unscrewed the old spray arm and then screwed the new part on. Less than 15 minutes. Works great!
Was this instruction helpful to you?
Thank you for voting!