FGIP2468UF0A Frigidaire Dishwasher - Instructions

Just unscrew the sprayer top, which Is 3 pieces, but should be one. Take new part, which all 3 pieces come as one piece, screw to the inside top of dishwasher and all done.

Isolated the leak and found the nut had split thereby allowing a loose seal and water penetration. Ordered 2 nuts just in case the other goes and the installation was easy. Unplug the unit, remove baseplate, remove screws under the countertop, and slide the unit out a bit. Use needlenode pliers to remove terminal connection and replaced nut. Reverse it for assembly. 3 minutes tops $6 later it is done. Easy money saved by a DIY.

Excuse me, as I do not know all the correct nomenclature, but I hope you get what I am saying. The new spray arm would not thread on to my dishwasher water supply coming out of the top of the box. Every time I would try, the supply line would push back up into the housing. Probably need to fix that too, but then I would have to uninstall the DW and just don't have time for that. My old part would thread right on, no problem, but the connection holding it all together was wore out. So I took the new arm and the old "nut" and put them together. They threaded right on, I pulled down on the arm and it is secure. So I had to Frankenstein it a little, but my DW is working, I didn't have to tear it apart and reinstall it, and I didn't have to replace it. Win Win!

I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!

Greg

The part wasn't correct and I have to pay postage back which is nearly as much as the part so it's stupid for me to spend more money on a part that want work I want order from your store again.

After getting a totally incorrect length of hose from partselect.com . Went to local hardware store and bought hose for $3.00 vs $20.99 + $10 shipping!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!

Had to shut electricity off and turn water off and disconnect them both. Take the screws out from underneath the counter. Slide out the unit disconnect the filler tube in the back disconnect the hose and replace and repeat the process to put it back together.

It took me about 30 minutes to do the repair - took my time and could’ve done it much faster.

Eventually broke off old heating element to get it out

Used the screwdriver to pry the upper rack left side tine up and out. Slipped the new one into place and pressed hard to seat the tine. this process took all of about 20 seconds to do.

watched a video, really easy fix. Solved the problem!

VERY simple repair - just unscrew the retaining nut by hand and hand screw on the new spray arm and nut assembly. A 30 second fix!

Easiest repair ever. The spray arm itself usually really is not the problem, it usually is the clip or gasket that holds the spray arm on. It wears out. This part is perfect for it supplies a new spray arm, nut and gasket/clip. I think it wears out due to a build up on the arm that puts too much pressure on the clip/gasket. Remember when taking the nut off, if you are standing above the unit with your arm inside, you turn the nut clockwise while looking down. Good luck.

unscrewed and remove the original mount....this is only hand tight. install new spray arm, hand tight only, threads are plastic and could strip if over tightened.

This part fixed problem. The original part seemed to have a defect. Was simple to fix, simply took off old piece still connected and hand tighten the new piece on, it took about 30 seconds.