EWDW6505GB0 Electrolux Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- C from Covina, CA
- Parts Used:
- 5304507354
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dispenser door broken.
Disconnect from power
Unscrewed 4 phillips screws from top of outer door.
Unscrewed 2 screws each siide of door.
Lower outer door section drops away.
Note wiring sequence on dispenser, then disconnect wires.
Unscrew 6 screws on dispenser and lift dispenser out.
Place new dispenser in place (note orientation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw.
Reconnect wires to dispenser correctly.
Slide lower outer door over tabs and secure with the 4 side screws.
Ensure lower door is up under control panel and secure with the 4 top screws.
Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done..
Unscrewed 4 phillips screws from top of outer door.
Unscrewed 2 screws each siide of door.
Lower outer door section drops away.
Note wiring sequence on dispenser, then disconnect wires.
Unscrew 6 screws on dispenser and lift dispenser out.
Place new dispenser in place (note orientation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw.
Reconnect wires to dispenser correctly.
Slide lower outer door over tabs and secure with the 4 side screws.
Ensure lower door is up under control panel and secure with the 4 top screws.
Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Coventry, RI
- Parts Used:
- A01986801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Center spray arm broke
I was able to pull out the top basket were the glasses are put then I lined up the back and the center plastic clip an slid on the center spray arm. It took about 2 miniutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Miami, FL
- Parts Used:
- 5304507354
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door on dispenser
The only difficultpart was to figure out how to remove the stainless cover from the door. Seems it slides upwards after screws are removed. After that it is self explainatory and goes back together in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tom from PASADENA, MD
- Parts Used:
- A01986801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Top spray bar rear gasket failed
Replaced the entire top rack with spray bar.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from IRMO, SC
- Parts Used:
- 5304507354
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Detergent Dispenser didn't work..
After turning of the power to dishwasher, I opened the door took of the two bottom screws on both sides of door. Closed the door and front panel just slide off. Then I took a picture of the dispenser to make use I could figure out how to put the wiring back together. Removed the six screws holding it in place and popped the dispenser out. Easy .. popped new dispenser in and lightly put all six screws back in ,wired it back up after checking my photo. Closed the door ,slid front panel back on opened the door put the 4 screws back in that hold the front panel .Turned power back on and Boom!! All done.. Not bad for a girl...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Fort Wayne, IN
- Parts Used:
- 5304507354
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dispenser door latch broke
removed the screws holding the door together, then removed the screws holding the dispenser to the interior door. replaced the wires and put the door back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from PASADENA, CA
- Parts Used:
- 154859401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom door gasket leak
No tools needed. Pull out old gasket. Clean the track. Ensure snug fit all across the track, use your thumb to push new gasket into the track firmly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- oscar from WOODBRIDGE, VA
- Parts Used:
- 5304507354
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken lid of the detergent dispenser.
The video show a different model, the only difference is that the screws for the top part shouldn't be removed only the ones that hold the front. Replace the detergent dispenser once the cover is removed is easy. All works like brand new. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raleigh from HOUSTON, TX
- Parts Used:
- 154671301
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Front rollers lost their wheels every time the tray was pulled out.
I got tired of having to replace the wheels. The wheels were essential for the tray to align along the tracks.Snap part into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Lorton, VA
- Parts Used:
- 5304507354
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rinse aid dispenser leaking and empty after 4 wash cycles
Needed to replace detergent / rinse aid dispenser unit on the inside top of door.
1) Need to remove outer door cover / panel by removing just two (2) screws - bottom screws on lower side panel. Door panel will drop vertically 1" to remove it.
2) Mark and disconnect the four (4) wires connected to the dispenser unit. The connections were so tight, it required pliers and a screw driver to loosen them.
3) Dispenser unit has four (4) screws holding it in place. Unscrew them and remove unit through door interior - this requires a bit of angling to get it out.
4) Position new unit through interior. Screw in place.
5) Re-attach four (4) wires in same sequence as disconnected.
6) Re-attach outer door cover. This is the most difficult part and really requires two people. It consistents of two sets of guide channels that most be aligned for the door panel to be secured re-attached.. Once aligned, the door cover must be moved vertically about an 1" and the screws re-attached.
1) Need to remove outer door cover / panel by removing just two (2) screws - bottom screws on lower side panel. Door panel will drop vertically 1" to remove it.
2) Mark and disconnect the four (4) wires connected to the dispenser unit. The connections were so tight, it required pliers and a screw driver to loosen them.
3) Dispenser unit has four (4) screws holding it in place. Unscrew them and remove unit through door interior - this requires a bit of angling to get it out.
4) Position new unit through interior. Screw in place.
5) Re-attach four (4) wires in same sequence as disconnected.
6) Re-attach outer door cover. This is the most difficult part and really requires two people. It consistents of two sets of guide channels that most be aligned for the door panel to be secured re-attached.. Once aligned, the door cover must be moved vertically about an 1" and the screws re-attached.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from HOPATCONG, NJ
- Parts Used:
- 154859401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The sensor showed an E1 leak which is "water underneath the machine"
Went to the website, viewed the schematic and ordered the two gaskets that form the seal around the door and tub, Gaskets should be ordered as a set if you have a leak and suspect the door. We saw discoloration at the bottom edge of the tub gasket indicating that there was water seeping through out onto the floor.The gaskets install by hand without the use of tools. Less than $100 in parts prevented the replacement of a $1,400 dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- S from ROHNERT PARK, CA
- Parts Used:
- 154740901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Removal handle had broken off making it hard to remove and clean trap.
Once replacement part arrived removed old broken item and snapped in new replacement item. Much easier to clean now. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from VERSAILLES, KY
- Parts Used:
- 5304507354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Would not dispense dish washing tablets
Turned power supply off to dishwasher Opened door and removed screws holding font of door Unplugged soap dispenser and removed six screws. Popped out and installed new dispenser. Plugged wires into new dispenser and installed front of door. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Gladstone, OR
- Parts Used:
- 154428403
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The brackets on the lower rack had worn out and not holding up the tines.
The parts came in a timely manner and took about 15 minuets to replace with no tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jill from Fort Wayne, IN
- Parts Used:
- A01986801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Spray arm broke
Popped off old remaining part. Popped new one on. Super easy.
Was this instruction helpful to you?
Thank you for voting!