OEMM1-CDU5JV Crosley Dishwasher - Instructions

Removed old gasket and simply replaced it with the new one. Very easy.

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

removed old deteriorated gasket - just pulled out
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.

still leaks - will investigate further

pulled out the old gasket, cleaned the area before pressing in the new gasket with my fingers ,I made sure to put it in the same way as the old one. You have no idea how happy I am that this solved the problem.

I removed the original gasket, wiped down the area, and installed the new gasket the same way the old one was installed. It was very easy.

just unscrew the inside panel. using a torx screw driver. disconect vericarefully the bad actuator and install a new one. put back everything in back order .

Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.

I used a voltmeter to see if 120 volts was present at the right time in the cycle; it was, so the actuator was the likely culprit. I ordered one on a Monday afternoon about 2:30, and it appeared on my doorstep Tuesday, shortly after noon! It took less than 15 minutes to replace the actuator - removing the 7 Phillips-head screws, lifting the panel, popping out the upper actuator, removing the two wires, putting them on the new actuator, popping it in and putting the panel back on. Worked like a charm. Happy wife . . .

I pulled out the old gasket and put in the new one. You need to stretch it a bit as you guide it in the track.
It was very easy but did not solve the problem.
Apparently, Maytag dishwashers are known for a leaky soap dish which I figured out after the door gasket was replaced. The problem is usually with the soap dish latch. You need to take the inner door off, disassemble the soap diehs, out a new gasket and latch on, reassemble, and you should be all set.

Pulled out the old gasket and pressed in the new one. No more leakage.

Ordered 3 parts first ..all came within two biz days..forgot the toe panel, called it was here the next day! The people that assisted me were wonderful! My husband did the repair. the dishwasher looks like new!!!!! I will order from Part Select again and again...extremley pleased. Now if only we could cover the Refrigerator in Black it would look like a whole new kitchen!

Removed dishwasher door liner and removed soap dish door latch assembly. Removed latch from assembly and replaced with new latch. Had trouble replacing assembly in correct sequence. Had to go on line and look at sequence picture to replace assembly correctly. Installed new gasket and replaced liner in door. The new gasket and latch solved my leak problem.
Thank you PartSelect

The dripping water was coming from bottom right side of the door, almost directly beneath the detergent dispenser. Looking closely at the drips, I could see that they were coming from saturated insulation that is between the inner and outer door layers. I took the inside piece of the door apart and sure enough I could see water had been getting through the door latch and running down the inside of the door. I could see that the grommet around the door latch was cracked and brittle, so I replaced it and was pretty sure that would resolve the problem. But when I put the door all back together and did a test run, I had a leak even bigger than the first, but this leak appeared to be through the door seal at the bottom right. I then ordered a new door seal, which took only 5 minutes to replace and resolved the leak. I think the old door seal was too worn out at that spot and just by removing and replacing the inside door layer, it must have not made a good seal at that point. But I recommend starting with the door latch and grommet first, since that is a $4 part, and then proceeding with the door seal, a $43 part, only if necessary.

I disconnected the dish washer and pulled it out. I laid it on its back, unplugged the electrical wires,removed the electrical magnet and pried the shaft seal out with a flat screwdriver. I gently packed the new seal into place with the flat screwdriver. I connected the electrical magnet and wires. I then installed the dish washer and ran it through a cycle. I am pleased to say the dish washer does not leak now.

***BEFORE STARTING BE SURE TO TURN OFF THE POWER!!
THE SPRING TENSION WAS GONE THAT WOULD KEEP THE DOOR FROM FALLING. KEEP IN MIND THERE IS A DOOR SPRING AND LINKAGE ON BOTH SIDES OF THE DOOR. SO BUY 2 OF EACH AND RETURN THE ONES YOU DON'T USE. IF YOU REPLACE THE LINKAGE ON ONE SIDE YOU MIGHT AS WELL CHANGE THE OTHER ONE SINCE IT'S ONLY A SMALL PLASTIC PIECE.
FOR ME THE SPRING WAS GOOD - ONLY REPLACED THE LINKAGE. REMOVED THE PANEL AT THE BOTTOM AND THE 2 SCREWS THAT HELD IT UNDER THE COUNTER TOP. I DIDN'T DISCONNECT THE WATER BUT WAS ABLE TO PULL THE UNIT OUT JUST ENOUGH (10 INCHES OR SO) TO GET TO THE SPRING. HELD IT IN PLACE WITH THE VISE GRIP SO IT DIDN'T FALL BEHIND THE UNIT. FYI - YOU MIGHT HAVE TO ADJUST THE TENSIONER ON THE BOTTOM IF YOUR SPRING TOOK A WALK WHEN THE LINKAGE BROKE. BE CAREFUL PUSHING THE UNIT BACK UNDER THE COUNTER. TOOK ME ABOUT AN HOUR AND SAVED SOME MONEY