CDB900NW0A Crosley Dishwasher - Instructions

Discovered upper wash arm had come off. It looked like it was repairable, but the bushing/clip holding the arm came off after one wash. Looked on line and reviewed part and saw it was a one piece assembly from photos. Removed old assembly by unscrewing from top of washer and screwed new assembly in place.

I installed the new spray arm without any tools and it worked perfectly.

I removed the old spray arm by pulling it off of the base then I pushed the new one on and made sure it was on properly then I pit the base back into the dishwasher and it was good as new!

Fully open dishwasher door to horizontal position, remove lower dishwasher rack and relocate to another temp location, grab old lower door seal from right or left corner and pull completely out of door, lay the old bottom seal aside facing the same direction as once installed (seal has a notched side which faces the right side of door), match direction of the new seal with the old seal (match the notched side of seal to the right side of door), gently push the seal into the door starting on the right side (notched side of seal fits tightly into a receiving area inside the door), and finally push the remaining portion of the seal into door (aligning with the right side already properly seated inside dishwasher door). Close dishwasher and run water cycle to confirm leak.

I was able to pull out the top basket were the glasses are put then I lined up the back and the center plastic clip an slid on the center spray arm. It took about 2 miniutes

First thing I did was turn off the power to the dishwasher, then remove the racks. Remove the foot plates, remove the two top screws holding the dishwasher. Then using the socket set, retract the two foot stands to pull the dishwasher forward. You may not have to do this step as I had to get it over tile. The pully springs are on the sides, easily replaced. After replacing the springs and I recommend replacing both at the same time, put everything back. The hardest part will be the foot plates, there are two and getting them lined up and the screws back in is a bit of a challenge. Then you are done.

All I had to do was take out old racks and replace with new ones. However the top rack did require taking off the part where the water runs through, it was easy though.

I would like to comment on how quickly and efficiently the parts arrived. I placed my order on a monday morning and am pleased to report by tuesday afternoon they arrived, much to my delight.

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

tossed the old one a replaced with a new.Hardest 10 second repair ever....It took 10 seconds had to open and close the door.

New one snaps into place easily.

Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings (~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.

unscrewed the old upper arm spray nut off and rescrewed the new one on....very easy...then I took the old gasket out of the bottom of the door and replaced by sliding it in. very simple....less then 15 minutes for both and have solved my issues.

Pulled out old gasket and shield guards and put in new ones. No tools needed. Piece of cake??

Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!

I unscrewed and removed the old Arm-Control fixture. I had a little (very little) trouble figuring out how to fit the gasket. It didn't go on like i thought it should. There was no gasket on the original fixture. So I put it on the way I thought it should go. I then screwed the new Arm-Control fixture on to the outlet. That was it. No tools required.