CDB900NW0A Crosley Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joe from Madison, WI
- Parts Used:
- 5304535382, 5304535768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed a replacement basket and lower rack assembly because the other ones had become rusty and cracked. Called and spoke with a sales associate to make sure I was getting correct parts. Received both of them quickly with a fair price and would use them again in the future.
Just swapped out the old with the new and it has been great. My wife is very happy and that make me very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Las Cruces, NM
- Parts Used:
- 154637401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
leaking dishwasher even when not in use
Remove water supply, take off two screws, attach new part reconnect water supply.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ashley from Littleton, CO
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm heat shield melted
Electrolux part number PS1524955, lower spray arm.
Problem. Dishwasher was spraying water out the bottom of the door. The spray arm was damaged when the heat shield overheated, causing the shield to contact the heating element. This resulted in the spray arm melting, causing water to be sprayed out the small gap between the dishwasher door, and the dishwasher bottom pan.
Repair
Lower spray arm is easy to remove. Release the arm clips at the center of the spray arm. When the clips are released, lift and remove damaged arm. Replacement arm is attached by pressing down on the center of the spray arm. The new unit has smaller heat shields so it will be less prone to overheating.
Thanks for the fast shipping. Part was recieved in a few days. For just a few dollars, the handwashing is over.
Problem. Dishwasher was spraying water out the bottom of the door. The spray arm was damaged when the heat shield overheated, causing the shield to contact the heating element. This resulted in the spray arm melting, causing water to be sprayed out the small gap between the dishwasher door, and the dishwasher bottom pan.
Repair
Lower spray arm is easy to remove. Release the arm clips at the center of the spray arm. When the clips are released, lift and remove damaged arm. Replacement arm is attached by pressing down on the center of the spray arm. The new unit has smaller heat shields so it will be less prone to overheating.
Thanks for the fast shipping. Part was recieved in a few days. For just a few dollars, the handwashing is over.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from Bellingham, WA
- Parts Used:
- 5304535251, 5304535768
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
The Upper & Lower dishwashing racks were rusting
I ordered the replacement racks to replace the rusted ones that had been in my original Fridigaire. I had to take the wheels off the old Upper Rack and attach them to the new upper rack, which was quite easy since they just simply came off by hand with a little bit of pressure. I also needed to take off the spray arm & spray arm funnel in order to attach them to the new Upper Rack assembly. I had to unscrew the spray arm funnel then unattach (without tools) the base of the spray arm from the upper rack. Then I could simply reattach the spray arm base by hand and re-screw on the spray arm funnel onto the base that had been attached to the new upper rack. I also had to take off the Shelf from the old rack and attach it to the new one (which was easily done with a little bit of hand pressure to unattach the Shelf from the old rack). All of this was much easier than I expected it to be, and much easier than I'm explaining I'm sure! I was able to do these rack switches without any tools which was great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Ozark, MO
- Parts Used:
- 5304525218
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Appliance read out "err", would not go on
It would sometimes work, which led me to believe it was a switch. Looked on line and found the mail switch to go on was in the latch. I took it apart, 6 screws, wiggled the switch and it went on. So I found the door switch to be bad. It was very simple to change the switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Alachua, FL
- Parts Used:
- 5304535768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rack had broken tines and rust
No repair, just replaced the lower rack. Your service is awesome. I received my shipment next day. Thank you so much. I will definitely use your service again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from virginia beach, VA
- Parts Used:
- 154773201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No water to dish washer
After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hummelstown, PA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking at the lower left side of the door.
Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.
Water leak solved...
Water leak solved...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from Desert Hot Springs, CA
- Parts Used:
- 154756401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The front door kept falling down
Broken friction cable on the right hand side. Remove screws that hold dishwasher to cabinet, pull out the dishwasher far enough to get to the friction cable and rear spring. Remove broken cable. Attach new cable to rear spring and connect to door hinge. Push back dishwasher and screw in the two screws that keep the dishwasher attached to the cabinet. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Clinton, OH
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Leaking Door
Pulled out old gasket from bottom of door with needle nosed pliers and then put in new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from Arkadelphia, AR
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
loose spray arm
Unscrewed the old spray arm and replace with the new spray arm.
The best part was in the ordering process. Having the diagrams with the parts let me see that I was ordering the correct part. Thanks!
The best part was in the ordering process. Having the diagrams with the parts let me see that I was ordering the correct part. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from YONKERS, NY
- Parts Used:
- 5304506516, 154406401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken upper sprayer
Unscrewed upper sprayer by hand, screwed new one in by hand. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from Bartlett, IL
- Parts Used:
- 5304506516
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Spray arm came off in wash cycle
The spray arm comes off into 3 parts but is really only supposed to be one. I removed the nut from the old assembly and attempted to place the new assembly on by hand. The new nut seemed to be slightly smaller than the original so it would not attach to the dishwasher. Using a kitchen knife, I removed the new nut from the arm unit and attached the new arm to the original nut and it went back on easily. The connection of the new arm to the new nut was 3 tabs that needed to be depressed with the knife and was a different conection method than the assembly that kept coming off in the wash cycle. The replacement part had a much better design than the original.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauren from Peabody, MA
- Parts Used:
- 5304535382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
large holes in the bottom of the basket where pieces of plastic kept breaking off
I replaced the basket. No tools necessary. New basket seems sturdier than original. Very satisfied with my purchase.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from Excelsior Springs, MO
- Parts Used:
- 154637401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
No water was coming into dishwasher.
Unscrewed dishwasher from cabinet and pulled out about 1 foot. Took bottom plate off of dishwasher. Undid clamp on hose of discharge of inlet water valve and removed hose. Shut off water to water inlet valve and removed. Took wiring clip off of water inlet valve. Removed 2 screws holding water inlet valve in place. Installed new water inlet valve in reverse order.
Was this instruction helpful to you?
Thank you for voting!