CDU2J3 Crosley Dishwasher - Instructions

Initially thought this issue was the dishwasher door gasket, but after reading post on this site about door latch grommet, removed 7 "hex screws" pulled inside of dishwasher door away and traced water from leak back to soap dispenser latch/grommet area so instead of ordering door gasket ordered door latch and grommet. Replaced grommet only (in addition to 7 "hex screws" had to remove 2 additional screws to get to it) which took some maneuvering. Re-aligned grommet and latch, inserted and tightened all screws that had been removed. Works great - no more water leaking!

Once I removed the inside panel from the door replacing the switch was pretty simple. completed the job in less than twenty minutes.

This was the third appliance I have repaired with the help of Parts Select in the last three months.

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

First I replaced the soap door grommet -- door still leaked. Then I went for the really expensive part ($40) -- the door gasket. The old one came right out and the new one went right in -- 15 minutes tops -- and the door no longer leaked.

Thanks to all the previous posters for their hints.

I removed lower cover panel. Removed two wires. (one on each end of the element. Removed two nuts on the element. Took out old part. Put new part in and reversed procedure. Works fine now.

I removed the screws holding on the interior door panel. This exposed the soap dispenser latch mechanism. After removing the two retaining screws I transferred the original parts to the new retainer and replaced the grommet prior to reinstallation of the mechanism and interior door panel. A savings of probably $100.00 or more for a service call and parts. Should last a few more years.

Removed 7 Torx Screws ... removed inner door panel ... snapped off the selinoid after noting the exact original position ... removed the Latch assembly 2 hex head screws ... removed the old Grommet which was crumbling apart ... stretched the new grommet in place. Then did the steps in reverse to complete a successful repair.
Thanks to your website, quick turn-around service and customer's repair stories, I probably saved a few dollars but mostly, I realized how much I love my dishwasher now more than ever!

Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.

The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.

Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.

Attempted repair was quick & simple. Removed 7 torx screws, and then pulled the wax motor out of its holder. Pulled 2 wires off, and replaced old motor with new motor. Reattached wires, & reassembled.
Only problem was this did not fix the problem, so back to square one, but worth a shot.

After pulling dishwasher out both springs easily installed using plastic connectors on the bottom left and right sides. Pliars were used to stretch the springs. It took fifteen minutes at most.

First I removed power to the dishwasher. The inside panel of the dishwasher door is held on with several screws with Phillips heads. Remove those and the panel comes off. There is a silver metal guard that you have to pull off being careful not to tear the insulation that is on the other side. Then there is one hex head screw to take off the handle latch assembly. You remove this assembly and take off the wires to the two switches on each side of the assembly. The replacement part doesn't come with the black plunger that pushes on the switch buttons so you have to remove it from the old assembly. This was the only difficult part, I essentially destroyed the old plastic assembly getting it out. But putting it in the new assembly was easy. Then I attached the wires to the switches in the new part and reassembled everything. Works like a charm now.

First I replaced the door gasket as every one else. This cut drips about 30%. I then discoverd that the Rinse Aid circular dispenser cap was opened about half way. I turned the cap tightly clockwise to close and cut drips to 90% total. I czn live with the other 10%,

I removed the inside door cover, unpluged the accuator, removed the two screws holding the dispenser latch in place. Replaced both the latch and rubber groumet. returned the door to normal operation and verified no leaks was present.

I first made sure the new gasket was long enough and it matched the original. Next I used the tip of a screwdriver to pick out a corner of the old gasket and then pulled the entire thing out. I noticed the old one stopped at the bottom of the gasket well. The new one was much longer and I thought I might have to cut it to length. Well I'm glad I didn't. If you start on the right side and work your way up and around with a 2 in. piece longer then what the old one was. I carefully tucked it in the bottom and closed the door. Glad I didn't cut the new one. Instructions would have been nice. Overall an easy fix. I'm very mechanically inclined so I knew better.

pulled out the old gasket, cleaned the area before pressing in the new gasket with my fingers ,I made sure to put it in the same way as the old one. You have no idea how happy I am that this solved the problem.