CDU650AWB37 Crosley Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sam from Philadelphia, PA
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Latch Asembly Broke, Door wouldn't close properly
The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Orlando, FL
- Parts Used:
- 99002659
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Wouldn't wash dishes
I have done two repairs, and both times PartSelect.com came to the rescue! The first repair was a few years ago when the dishwasher would run but nothing got wet. It made all the right noises except the sound of water being thrown around, because no water was being pumped! This resulted from a cheap plastic "chopper" assembly that stripped and wouldn't drive the impeller. PartSelect sold me a solid metal replacement part for under $10 and that fixed the problem for several years.
Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!
Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dr luther c from state college, PA
- Parts Used:
- 99002947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Wheel broke on top rack of dishwasher
Removed the rack from the dishwasher.
Took off the adjuster from the rack using the allen wrench.
Replaced the new.
Perfect
Took off the adjuster from the rack using the allen wrench.
Replaced the new.
Perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from SPRINGFIELD, VA
- Parts Used:
- WPW10117748
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher leaking.
Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Crockett, CA
- Parts Used:
- WPW10261227, 99002780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One of the wheels was missing from the lower rack and a rack stopper was also missing from the the top rack.
A really easy and simple repair that required no tools. The parts were delivered within a matter of days. Completely satisfied with transaction and results.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Chester, NH
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not shut
Easy! Unscrewed panel, took off old latch, put on new. Took about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- betty from GEORGETOWN, TX
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Basket broke----bought a new one!
opened door---- took out old basket--threw it away. set new basket in its place!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from BLUE SPRINGS, MO
- Parts Used:
- WP6-917644, WP6-917642
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
WAS NOT GETTING DISHES CLEAN
UNSCREWED THE LOWER PART BY PLIERS AND HAND. COULDN'T UNDERSTAND WHY THE LOWER
PART WAS AVAILABLE BUT THE UPPER SPRAY ARM
WAS NO LONGER AVAILABLE WHEN THEY BOTH GO TOGETHER..
PART WAS AVAILABLE BUT THE UPPER SPRAY ARM
WAS NO LONGER AVAILABLE WHEN THEY BOTH GO TOGETHER..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert d from MOORHEAD, MN
- Parts Used:
- WPW10275768
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door didn't seal tight. So when it would go into rinse mode it would leak water on my floor
The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 bucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from WHITE PLAINS, NY
- Parts Used:
- WP6-919539
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Soap not disolving and leaving residue on everything. Not Cleaning.
Followed the instructions to dismantle all the way down to the motor. Replaced the stripped plastic shaft with the metal one. Clean dishes every time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barb from TWINSBURG, OH
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The silverware basket needed replacement since there were cuts in some places on the bottom which caused utensils to fall partway through.
Very simple. Just replaced the old one with the new one. Voila!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from NEWNAN, GA
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Basket had holes in it from repeated use of holding sharp utensils.
Just replaced with new basket. Fit like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MARBLEHEAD, MA
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Some of bottom wire in the silverware basket had rusted out allowing silverware to fall through and interfere with rotating arm.
The "repair" was actually a replacement. My wife did it. She took out the old, damaged basket and dropped in the new, replacement basket. She removed the slotted lids because she doesn't think they are necessary and she doesn't like them. I got the old basket for holding small items in my workshop. The lids will be thrown away, unless I can come up with a use for them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Groff from WVisconsi Rapids, WI
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The bottom of the old basket was breaking and silverware was getting stuck
Open the door and remove old basket. Place the new basket in its plave. Time elapse approximately 20 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from STURGIS, KY
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced silverware basket. No problems!
Lifted out old silverware basket. Set new basket in. Took approximately 20 seconds.
Was this instruction helpful to you?
Thank you for voting!