SHX4ATF5UC (12) Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from Broomfield, CO
- Parts Used:
- 00611332
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dishwasher not draining at end of cycle
My Bosch dishwasher is approx 11 years old. It was leaving water in the dishwasher pan at end of the cycle.
I replaced the drain pump component, which is accessible by removing the lower front panel. It is not necessary to remove the dishwasher door panel to access the pump, but may help with accessing the pump if you have difficulty getting it to come loose.
On the initial install of the new pump, It wasn't fully seated so it dropped a bit. Make sure the pump is fully inserted (push on it or use a bit of Vaseline on the rubber). Once fully seated it no longer dripped and the dishwasher is now draining properly.
Steps
1. Shutoff power at breaker
2. Remove lower access panel at front of dishwasher
3. Remove filter, drain and retaining clip from tub, empty water from tub with sponge or baster
4. Unplug drain plug wiring connector (small clip on right)
5. Twist old drain pump unit clockwise to remove
the old unit (have a towel ready to catch any water left in the tub)
6. Connect new pump to wiring harness
7. Insert the pump at 2 o'clock position, ensure it is fully seated (see note above).
8. Twist pump counterclockwise until it locks into place. The pump should not wiggle and be firmly connected to the unit.
9. Replace tub clip, drain screen and cover
10. Turn power back on, run cycle to test for operation and leaks
11. Reinstall lower access panel.
I replaced the drain pump component, which is accessible by removing the lower front panel. It is not necessary to remove the dishwasher door panel to access the pump, but may help with accessing the pump if you have difficulty getting it to come loose.
On the initial install of the new pump, It wasn't fully seated so it dropped a bit. Make sure the pump is fully inserted (push on it or use a bit of Vaseline on the rubber). Once fully seated it no longer dripped and the dishwasher is now draining properly.
Steps
1. Shutoff power at breaker
2. Remove lower access panel at front of dishwasher
3. Remove filter, drain and retaining clip from tub, empty water from tub with sponge or baster
4. Unplug drain plug wiring connector (small clip on right)
5. Twist old drain pump unit clockwise to remove
the old unit (have a towel ready to catch any water left in the tub)
6. Connect new pump to wiring harness
7. Insert the pump at 2 o'clock position, ensure it is fully seated (see note above).
8. Twist pump counterclockwise until it locks into place. The pump should not wiggle and be firmly connected to the unit.
9. Replace tub clip, drain screen and cover
10. Turn power back on, run cycle to test for operation and leaks
11. Reinstall lower access panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from STATEN ISLAND, NY
- Parts Used:
- 00611332
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Error code E24
when you receive the drain pump and you are ready to install make sure you put VASELINE around the rubber Gromit that will make putting the drain pump in very easy, also to give yourself more space to remove and install the pump remove the front door panel.
It took me 20 minutes from start to finish
It took me 20 minutes from start to finish
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MONTROSE, CO
- Parts Used:
- 00611295
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
On/Off button not working properly
Turned power off, disconnected plug from switch, R&R switch, reconnected plug and restored power
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from PARSIPPANY, NJ
- Parts Used:
- 00611475
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Four wheels on the lower dishwasher rack came off and got lost.
I bought replacement wheels.
I put them on the post, and they snapped onto the vertical post very easily. Job done.
I put them on the post, and they snapped onto the vertical post very easily. Job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from WESTMINSTER, CO
- Parts Used:
- 00611332
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher would not start and had not completely drained.
Tried the door lock first. Did not fix the problem.
Replaced the drain pump and it fixed the problem.
Parts Select identified the pump as the most frequent problem.
Next time I will order both parts when one is cheap for any repair.
Find Parts Select is very helpful. They have identified a problem with a washing machine in the past.
I will use them for future problems.
Replaced the drain pump and it fixed the problem.
Parts Select identified the pump as the most frequent problem.
Next time I will order both parts when one is cheap for any repair.
Find Parts Select is very helpful. They have identified a problem with a washing machine in the past.
I will use them for future problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John D from Ocoee, FL
- Parts Used:
- 00611332
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
E-24
Removed old discharge pump and replaced it with the new one. After four attempts the dishwasher worked once. This cycle continued for the next 3 attempts then it stoped all together. Ordered the sensor, installed it snd the dishwasher still doesn’t work! Now what do I do???
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toni from GREENSBORO, NC
- Parts Used:
- 00611475
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One Dishwasher bottom rack wheel broke
Popped the new one right on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from ELGIN, TX
- Parts Used:
- 00669221
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
the door has to be taken apart.
My son and my husband did it. I watched.
They both injured their fingers.
But it stopped the leak!
They both injured their fingers.
But it stopped the leak!
Was this instruction helpful to you?
Thank you for voting!