ADB1500AWS3 Amana Dishwasher - Instructions

Used utube to replace the inner seal. Did not stop the leak completely, had to replace the entire door seal and level the machine.I did the inner seal myself, but had a repairman under our homeowner warranty do the rest.

First, turn the power off to the dishwasher. Then removed several screws that hold the panel in place. These are mostly on the side of the panel door. I then pulled the old panel and put the new one in.

The repair was simple. My husband replaced the panel in about 30 minutes. The dishwasher looks brand new and updated and it saved us about $600.

Remove mid and bottom rack. The nut on the bottom spray arm can be removed by hand; all screws are T-20; just hold on to the impeller to turn its screw. I keep a T-20 under the sink, which tells you something about how reliable we've found this model! Remove screws as you go down, replace parts as you go back up; assembly is reverse of removal, yadda, yadda. Don't miss opportunities to notice how Maytag keeps making small improvements to many of the parts, wonder whether in a few more years of purchasing replacement parts for this thing it will finally stop breaking. My wife informs me that plastic mesh filters like Maytag uses are something she buys for her lab as disposable single use items. We actually had a Bosch on order (metal filters) but I decided to give this unit one more infusion of parts. It's working better now, but I don't know how long it will last before something else gives out.

I called for a Lowes where I purchased the dishwasher was told it was out of warranty, they set up for a repairman to come out and fix it. He came out and told me it would be $190.00 for parts and labor but that didn't include the service call of $60.00 dollars. Total bill would be $250.00, plus it would be another 2 weeks before he would be able to get back because he had to order the part but and get this I would get the part delivered to the house before the two weeks, and that he wouldn't guarantee the part for more then 90 days.
I told him no way, so I researched the internet and found this site part cost $25.00 dollars my time about 30 min. SAVINGS of $225.00.
The part was pretty easy to install had to take out a few screws around the edge. Only trouble I had was putting in the handle but I figure that out and put everything back together again.
I would purchase parts from this company again had it within 2 days, at a very reasonable cost.

Took off the small plastic nut -- you can do it with your fingers. If it's too tight, use a pair of pliers.Lift off the old arm, put on the new arm. Very simple. Takes 2 minutes.

It was very simple and easy. I opened the panel inside the door; total of 8-10 screews. The latch has two electrical connections and switches. The replacement part I got came with an extra set of switches. Replacing the switches needed an electrical tool which I don't have so I decided to keep the old ones. It is quite easy to take out the switches and replace the latch. I should have taken out the power; but I did not. I was just careful handling the wires et al; no big deal either. My dishwasher is working fine now. I was able to fix it within $40 and 1 hour of effort. Any technician would have cost me atleast couple of hundred bucks + parts etc.

Went fine..video made it easy..one of the best instructional

also had to replace heating element. Had to remove dishwasher from under counter to get to heat element. Initial installer used long braided steel water line and plug in electrical connection so removal was easy (10 min). Pulled (2) electrical terminals from heat element and (2) plastic retaining nuts put in new element w/matching nuts,element came w/seals. Check for leaks before installing back under counter. Then removed torx screws holding impeller cover and accumulator/filter removed old put in new after good cleaning of course. All is well.

Took the door of the dishwasher apart and the replaced the lever assembly. The lever assembly does not come with a door handle, so you have to remove the old door handle from the old lever assembly and install the door handle on the new lever assembly. Installing the handle on the lever assembly was the hardest part, the rest of the installation was easy.

Repair has been delayed due to the fact that I do not own the right size bit for the screw.

After checking the door switch I found the micro switches were working but the unit would not start on the control panel. Thinking the latch was worn, I ordered a replacement. After changing the replacement latch and switches that came with it, the unit would still not start. I checked the switch and it is making contact. I can start the unit after I close the door using the handle of a pair of pliers. So I assume the control board is bad, due to the fact that it will not initialize the control panel until the door is closed. Now I have ordered a control board and will replace...stay tuned!!

After prying open the door i removed the inner skin cover which did provide me access to the latch assy,2 additional screws and it was fixed.

This appears to be a problem with this apliance since it has done this before while under warranty

Matching the part I had in my hand with the picture online was a cinch. Rec'd the latch in a few days, and installed it in minutes. Why did I wait so long to look it up and order? At least the kids think I'm a hero for fixing the dishwasher!

Removed the screws that attach the inside of the door, keeping them in order. Two are longer. The part is loose at that point and the wires un clip with a little pull with a needle nose. Replaced with the new part, re screwed and good as new. oh and turned off the breaker before disassembly.