ADB1500AWS3 Amana Dishwasher - Instructions

Removed two screws at the top of the base washer. Three screws removed down both sides of the base washer. Lifted washer out enough to see the cable and spring connections. Removed cable and replaced with new and re-connected. Slid washer back into position and installed screws.

Ordered part. (Part was larger than the original . That is it dis not fir int supports tha same as rhe original. Hut i modifird the support by assin copper wire to fanten the heater to the supports.) The instalation was no pronlem with a little engineering. Works like a charm, Wife Happy Most important result.
Elmer

1. remove inside door panel
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).

Pull dishwasher about 1/2 out of cabinet. Remembered to turn off power just in time. Removed electrical leads. Hand removed nuts retaining the heating element. Installed new element - hand tightened nuts.

The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.

The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.

Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.

The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.

Remove screws holding the existing white panel. Once that panel was loose, there are several screws internally that have to be taken out in order to fully remove the panel. The new panel is then installed by putting it in place and reinserting the screws. It is an easy"fix" to change the DW to match other stainless steel appliances. You do need to be careful to make sure the door springs stay attached.

Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.

UNSCREWED THE LOWER PART BY PLIERS AND HAND. COULDN'T UNDERSTAND WHY THE LOWER
PART WAS AVAILABLE BUT THE UPPER SPRAY ARM
WAS NO LONGER AVAILABLE WHEN THEY BOTH GO TOGETHER..

Easy! Unscrewed panel, took off old latch, put on new. Took about five minutes.

I followed the instructions here on PartSelect to dismantle and put the new impeller in to place. Could tell the difference just in sound alone once it was running.

Pulled dishwasher out far enough to get at the original hose. Disconnected and drained the hose. Connected new hose, zip tied the hose in place, pushed dishwasher back in place and re-anchored. Zippidy do...piece of cake. Perfect fit.

I took out the racks and disassembled the bottom assembly until I got to the impeller. Just replaced the part and reassembled. I used only a star shaped driver on all tightened pieces. It was very easy to do and I did not even need any advice/help from the hubby! Saved a whole lot of time and money doing this small repair myself. Thanks for fast service. I ordered part online Thur. late afternoon, and it arrived Friday.

First I removed the screws from the inside of the door exposing the latch assembly. Removed the old part and installed the new assembly. Don't screw it on to the door untill the cover is on again.
First I ordered only the latch without the handle. Found after opening it up the handle was broken on the inside so had to order the assembly. It's a piece of cake to install. If you're having touble opening the door don't think because the handle looks ok from the outside it's not broken.. probably is. Partselect.com is the greatest company to deal with. I'd recommend them to anyone and have.
Sam