ADB1500AWB46 Amana Dishwasher - Instructions

Orderd the part's from your web site (recived my order in a timley fasion thanks) the parts just sliped on and clipped' basket rolls great. Mike Schaffer

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

I know that I have very hard water, but am reluctant to get a softener. I hope that changing the "guts" of the water delivery to my dishwasher will help...already replaced the filters which helped too... so far, it's a little better.

Installation was a breeze. Took off the upper, middle and lower spray arms. Had to loosen screws in filter assembly to remove old manifold. Popped everything into place... had to scrape mineral deposits off clips that support manifold and upper spray arms.
Easy...

1. Removed door inside plastic panel, 2. Removed additional screws holding panel to hinge brackets and control panel, 3. Figured out that this would all have been easier if I'd unhooked door hinge springs first (access from sides), 4. Removed isulation from old panel and reglued to new panel, 5 Reassembled, hooking up door springs last. Voila!

Removed the top rack and unscrewed the six screws involved on the rack adjuster. (Take note on how you took the thumb adjuster on top off for easier reassembly) Replace assembly on rack and slide rack back into dish washer. Kudos to PartSelect for getting my part here in less than 24 hours on a normal delivery charge.

Very easy after watching the video. thanks

You just remove the old unit and set in the new unit. the wheels were already connected.

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

Shut off the electricity to the dishwasher. I removed all 11 screws from the door panel. After separating the 2 door panels, I removed the 2 door switches from the door handle ( I used a flat head screw driver to help get them out). Then I unplugged the 2 switches and plugged in the new ones. I replaced the door switches into the door handle ( this was not an exact fit because the new switches is slightly larger than the old ones). I put the new switches in place as tight as I could in the handle. I screwed the 2 screws holding the handle first to secure it before I put all the other screws in the door panel. I turned the electricity to the dishwasher back on. Our dishwasher has been working perfect ever since then and it is over 10 years old.

replaced rack

First I made sure the breaker for the appliance was turned off!

I only had to unscrew all the screws from the inside door.

Next I used pliers to pry the old Latch Assembly (it is all pig tailed so only to plugs to undo).

Next, I snapped the new Latch Assembly into the two sockets.

Screws were replaced and wa la!

Turned breaker on and tested. Easy as pie. Took about 10 minutes from collecting the tools, fixing the problem, and replacing all the tools.

I actually had my 14 year old daughter do it so that she could learn how to make small repairs. This would have easily cost approximately $150 for a repairman to come and fix.

Then we went to the garage and unstuck the valve on the carberator to our '75 Chevy! (it was cold).

Not bad for a couple of girls!

I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.

No repair needed, just inserted the new dishrack. My only complaint is the lack of upright tongs in half of the rear section of the rack. This limits the number of dishes that can be stored. My original rack had tongs in all areas which better suited my needs. If there is a replacement that better suits my needs I would like an exchange.

Pulled out the old one and put in the new one!