ADB1500AWS1 Amana Dishwasher - Instructions

I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.

First, I removed the screw, then I took off the old wash arm, then I replaced the wash arm, and replaced the screw. Nothing could be easier!

Snapped the old part out and snapped the new part in.
It was a piece of cake.

I unscrewed the inner door panel and the old latch assembly came out. I went to the circuit breaker and cut off power to the DW. Then I unplugged the old latch assembly and plugged the new one in. There were some springy metal pieces that had to be pushed back to get the old plug off and the new one on. After that it was just a matter of aligning the holes of the latch assembly with the holes for the screws and replacing all the screw holding the door panel, and tightening them up.

I was extreemly pleased with the replacement handle unit. The original unit had a plastic pivot points - the replacement part replaced these points with metal rods. The pivot points on the old unit were the points of failure.

The repair should have been done with a "star" head. Not having this, I was able to use a hex wrench instead.

The repair time was less than 10 minutes, most of that time removing and replacing the star head screws. If you have removed the old part, you have essentially completed the repair.

The biggest problem was identifying the proper handle unit. There are two very similar. Measure the distance between the mount holes in the unit and refer to the grid in the picture. The grid on your site was extreemly helpfull given the lack of part numbers printed on the Maytag OEM parts.

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

First I removed the torx screws halding the inner door panel on. I then seperated the door panel from the door and removed the latch assembly and disconnected the switches from the latch. After installing the switches on the new latch I replaced it between door and inner panel. Finally I replaced the torx screws and was finished.

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

Repair was fairly easy. There are 11 screws You have to remove then simply unplug the electrical connection from the door latch/switch and plug in the new one line up the screw holes tighten them down and your in business.

I removed the 11 torx screws which hold the cover in place. Then I had to remove the electrical connectors from the old switch (a flat head screwdriver or something else to break the connection helps). The new one plugged right in, and was back into place in minutes. The rack stop was just a remove and replace. Extremely easy!!

1) Turned off the power

2) I removed the screws on the plastic door.

3) The latch/handle assembly was right there.

4) I noticed that white and black wires fed each side. I noted which side did the black feed and the white feed.

5) I took a pair of pliers and held the white wire brackets and pulled the metal parts off. This is where the time took.

It took about 2 minutes per side.

6) I then slid the new metal parts in the white brackets.

7) I screwed it back.

8) Turned it back on!

9) Works great

Pretty easy job. You need torx tips for your screwdriver. An electric screwdriver got all 8 or 9 screws out of the door panel in about 60 seconds, separated inner door from outer door, pulled out handle assembly & disconnected wires, attached wires to new assembly, screwed it all back together. Be prepared... the handle will break again. It's just a bad design by Maytag. This Maytag model is so bad the company discontinued it. Beware of the control panel getting corroded from steam & failing. If replacing this panel, make sure you seal where the cable goes into the touchpad with some kind of waterproof glue, nail polish remover, or sealing tape so it doesn't happen again.

1 - Unscrew the back of the dishwasher with a hex-type driver. The latch assembly will be resting inside the outer door assembly. Make sure power is turned off to the washer - there are a couple of "hot" wires that will attach to the latch assembly.

2 - Unplug the wires from the old latch and plug into new latch assembly.

3 - Place the latch assembly back in place and re-attach the two door pieces together.

4 - Turn power back on at the breaker.

5 - Load dishwasher with the stuff that's been sitting in your sink.

6 - Gloat to spouse/significant other that you just saved $100 by fixing it yourself.

Just a quick note of thanks for shipping the replacement handle for my Maytag dishwasher.  Service was superquick and I was able to save big bucks (no service call).  I called on Saturday evening and the part was here on Tuesday.  The young lady who helped me was awesome and a Pens fan to boot.  I seldom send these types of emails but my experience was worth sharing.