ADB1500AWS1 Amana Dishwasher - Instructions

1st, shut off the breaker for the dishwasher.
2nd, opened the door and removed all of the torx screws holding inner door to outer door.
3rd, placed inner door up and held it out of the way (closed inner door through/around latch tab and folded up a piece of paper, threaded it through latch tab hole and placed a small piece of masking tape around the paper to hold door out of the way - this made the entire job easier, because you do not need to hold the door out of the way anymore).
4th, removed broken latch/handle assembly (carefully - it is always a good idea to collect/save broken pieces to piece together the "puzzle" in case you need to improvise. Removing the metal clip attachments is tough, but much easier now that the inner door is secured out of the way. They cannot simply be pulled straight out. You should use a gentle back and forth wiggle motion in a T-shape. Meaning, wiggle back and forth 1-way, and then the other way (perpendicular to the first way) - this should get them separated. Be patient with this procedure - it will work fine and you won't get frustrated.
5th, look at the situation to determine exactly what went wrong/broke specifically (I was extra screwed, because 1/2 of each of the "U" shaped tabs that hold each side of latch assembly in place were broken - as well as the tabs on the latch assembly. These U-shaped tabs were/are actually part of the plastic outer door. Specifically, they are on the inner side of the plastic control panel display. I could have replaced this part too, but I was trying to do as inexpensive a repair as possible.
6th, So - I found 2 nut/bolts in my toolbox (probably 1/8" in diameter - 3/4" in length - I used flat head. Be careful in your selection of bolt length - the least amount sticking out the front of the dishwasher - the better). I drilled 2 holes - in the exact location where these inner door tabs broke off - and entirely through to the outside of the outer door - yes, all the way through. We are talking about drilling through less than 1/4" of plastic - simple. I made sure that I would not be drilling through any lighting display or really important pieces. The holes ended up being situated in plain plastic locations - not interfering with any functions. Be careful in your selection of drill bit size - you want the bolt to fit through the hole obviously, but you don't want the bolt to have too much wiggle room - because it will be functioning as your new tab - that should have as much structural integrity. So, I recommend drilling a hole that is just big enough that you have to use a screwdriver to thread the bolt into the hole.
7th - I connected the clips into the new latch assembly - somewhat easier than separating the old one.
8th - I placed the new latch/handle assembly into its proper location (resting on the 1/2 mounting tabs that remained on the inner door).
9th - I then used a small flat screwdriver to thread the 2 screws in place (yes, screw head on the inside of the door - to function as a tab - the edge of the screw head will hold down on the latch tab ends). I had to tilt the latch assembly forward, to allow just enough clearance to get my small, thin flat head screwdriver in there (on a slight angle, but that's ok). Thread it through until it gently snugs down onto the latch tab.
***You can do better than I did if you want to go the extra mile*** Find a small, thin piece of sheet metal or plastic. Drill a hole just big enough for the bolt threads to slide through. This sheet should be cut to the following specs: a rectangular shape just big enough to span across the tab you made with the bolt - onto the inner door tab that it still not broken (the drilled hole to fit the bolt threads through on one end). It is added structural integrity to even better hold the new latch assembly in place. Think of it as a bridge that spans the tops of the U-tabs.
10th - After screwing the bolts through until just enough to snug down on the latch assem

This repair was very easy. First, I opened the dishwasher, removed the screws (they are torx) and removed the old handle assembly. I removed the inner liner from the door, and to do that I had to pull out the electrical wires. I turned off the power, always a good idea. I should have marked the polarity on the plugs before removing them, since you can put them back on wrong (and I did).

I also used caulk to hold the assembly on the bottom, since the cheap plastic molded forks holding the assembly on had broken. Most of the holding force comes from screws at the top. The caulk provides just a little adhesion, and will be easy to remove if the handle should need to be removed again--which I consider unlikely.

This was a very easy repair. Before I did anything, I flipped the breaker for the dishwasher and tried to turn the dishwasher on to make sure it had no power going to it. Once I was certain the power was off I removed the hex screws (there are 11) on the inside of the door panel using the hex screwdriver. Lifting and holding the inside panel up, I then used the pliers to pry the old latch assembly out of its metal prongs. Then I replaced the old latch assembly with the new one, pushing the metal prongs (by hand) into the slits of the new latch assembly. Last, I lined everything up and screwed the door panel back in place. I flipped the breaker back on and activated my child lock to make sure I had power. The handle worked perfectly. Quick and easy fix!
I ordered the part with 3-5 day delivery and actually received it in 2 days! I'm extremely pleased with my partselect.com experience and highly recommend using them for all your appliance parts needs!

I could not reach the heater element nuts from under the dishwasher so had to pull out the dishwasher. I removed the screws around the front of the dishwasher and pulled it about half way out before the water inlet pipe and the electrical wires stopped me. I shut off the water, unhooked the copper pipe, and unhooked the electrical wires (shut off circuit breaker first). Pulled the dishwaser out so I could remove the element nuts and wires to the element. Removed the old element and installed the new one - the old nuts would not fit. I went to a local appliance parts store and found that my element is no longer made. I had the correct replacement element but you need to order the nuts also. Luckily, the local store had a small brass nut that worked. Reattached the electrical wires to the element, pushed the dishwasher half way in, reattached the water inlet and electrical wires, pushed the dishwasher all the way in and scewed back into the cabinets. All is well now and the dishwasher is working much better.

The spring mechanism is on the side, so you have to pull the dishwasher out onto the floor. To do that, you have to remove the floor molding (preferably without breaking it) and remove the base coverings (painted metal plates on the bottom of the washer. Unscrew the side gasket plates on the side of the dishwasher (just inside of the door) where it attaches to the cabinet and the screws in the braces at the top (inside the door) where it attaches to the counter top. Now you will be able to slide the washer forward to look at the sides where the door springs are. Depending on the floor, you may have to raise the washer's front feet. They screw up. As you pull the washer forward be careful to not mess up the insulation which drapes over the top and sides. You only need to come out 1/3 of the way to see the sides where there is a plastic wheel at the forward bottom corner. As you move the door up and down you can see the hook where the cable goes and further up the side you can see several notches where the spring goes. Hook the cable and bring it around the wheel and attach it to the spring. To reinstall, just follow these directions backwards. Good luck.

I wanted to get the dishwasher cleaning better and thought that maybe the accumulator needed to be replaced. I figured that I'd swap out all the spray arms as well, just for good measure.

I needed Torx screwdrivers (T15 and T20, I think - not 100% sure on that) and patience because there's really quite a lot of screws to get the accumulator out. Finally got to it and it didn't look damaged, but replaced it anyway.

The spray arms are easy - they just snap in except for the lowest one, that had a plastic nut. I ordered a replacement nut just in case I broke this one (you know how that goes) taking it off. Well, it took pliers, but it came off ok.

In the end, my dishwasher is happy and cleans much better now.

The original brackets that hold the water distribution manifold to the back and top of the tub came off the "X-shaped" plastic posts on the tub walls. That caused the upper wash arm to sag down into the travel of the upper dish rack and was broken off when the rack was pushed in.
I bought 2 new brackets and a new wash arm. The new brackets had a smaller aperature than the originals and fit tightly onto the plastic posts, holding the manifold firmly in its proper location. Replacement of the brackets and the new wash arm took less than ten minutes and required no tools!

Not being very computer literate, the most difficult part of the entire venture was navigating your web site. But I finally found the part I needed. I paid on line with a credit card, and received the part within a few days. I popped it in the dishwasher, and it took three days before my son noticed it.
He was surprised and I was proud to say " I ordered it on line."
All's well that end's well.
I would difinately use your service again.

I unscrewed the door panel. removed the plastic cover protecting the dispenser. unscrewed the dispenser (6 screws). I removed the old dispenser and put the new one on and put it all back together. It was pretty easy.

disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes

First replaced rubber seal around door, which did not stop the leaking.
Then ordered insulation foam strip and replaced old one, which fixed problem. Put new strip over the old one because tub was slightly warped.
Very pleased with order speed and cost.

Unpluged the electric, Disconnected the water line and the drain line. Removed the dishwasher. Removed and installed the new water inlet valve and the float switch. This was a very simple repair. Reinstalled the dishwasher and connect
the water and drain line. Pluged in the power line. Turned the dishwasher on and it worked perfect. Thank you for the correct parts.

This isn't a how to fix it....it's what part was bad. I had originally contacted the local Maytag repair center and the owner swore up and down that our problem had to be the thermostat and not the heater. He said he had only replaced maybe 5 heaters in 15 years. But our heater looked like heck, with hard water deposits and all, and it wasn't that old, but we went ahead and ordered the thermostat from PartSelect, which came in a day. The problem wasn't the thermostat, so we ordered the heater from PartSelect (again, only one day delivery) and our dishwasher is working again. The heater coil actually had a hole in it from some sort of corrosion. My 18-year-old son did the repair job in a jiffy.

After replacing the door gasket and seeing that this wasn't the problem, using the schematics found at partselect.com I finally realized that it may be the insulation foam strip. I ordered the product and received it very quickly. Installation went fairly quickly. It was easy to remove the old foam strip and install the new one. The only problem was that the foam strip was about 1/4 " too short and it didn't cover the entire bottom. I improvised a little bit and cut off some of the old strip and covered the gap. So far the leak seems to have been fixed. In addition to the foam strip I had to buy a torx screwdriver for $11 at the local hardware store. The total spent was around $25.

All that was broken on the old detergent dispenser was the door but the door can not be ordered without buying the whole detergent/rinse aid assembly. When I got the new item I just removed the old door and replaced it with the new door that I had taken off the new one. I still have the new detergent/rinse aid assembly that I can keep if I need to change it in the future.