ADB1500AWS1 Amana Dishwasher - Instructions

the new dishrack fit right in immediately with no tools needed. Delivery was prompt

I pulled the unit from under the counter. the springs and cables are on the front sides of the dishwasher. I moved the insulation removed the broken spring and cables and replaced them with the new parts. just one side was broken, but I replaced both while I had the unit out.

I removed the 11 screws that hold the plastic inner liner to the outer sheet metal of the door. The latch will be right there, and very easy to access. I Just removed the two connectors for the wires, which are a bit stubborn, and used a pliers for leverage to get them off the latch. Installed them on the new latch, and put the door halves back together, and ran the 11 screws back in. A side note, I have noticed that on the plastic front panel that houses the buttons, that there are two plastic tabs that are cast into the unit, that are chronically broken. They are there to help hold the latch solid when you put the two halves of the door together. I have been really easy on the door, but they still break, but it seems to work pretty well without the tabs intact. This happened to me twice, because I replaced the front upper panel on it, and the same thing happened again. Engineering issue I assume. Overall, a quick and simple install.

The initial repair was more involved due to figuring out how to get at the problem. A foam sealer strip located at the bottom of the inner door had lost it's seal. I first sent off for one and it was of relatively thin material. It was carefully installed but still leaked. I ordered another one from Part Select and it had thicker foam. It was installed right over the previously installed strip and made a tight seal. (knock on wood)

Removed plastic lining from dishwasher door with torx screwdriver, then removed screw holding door latch assembly in place. Removed existing switch from door latch assembly and replaced.

This switch was not the correct one initially as it was a normally closed switch, whereas the existing switch was a normally open. Was able to pry open the switch and switch the contacts to normally open so it worked out in the end. Would recommend purchasing the complete latch assembly w/ switches if you aren't comfortable taking the switch apart.

first i removed eight torx (t-20) size screws...from the inner door . Then the wired harness surrounding the latch handle...( just a warning..im very very handy..esp with electric and got a little too cocky....pls make sure you turn off the power to the dishwasher...and avoid being zapped as i did ok?) the replacement part snapped in perfectly and was actually better quality than the maytag original...all it took then was to put the eight screws back and the washer was up and running in about 1o mins..

took the bottom spray arm & lower plastic pieces out, unscrewed the impeller & replaced it. the original impeller which holds the disposal blade down & wore down & no longer retained the blade. snap.

Replaced the door seal. Removed the old seal and gently stretched the new seal and pushed it into the channel. Snipped off about 2 inches excess seal. As far as the Inner Door Foam Insulation Strip goes, it was not as easy. To begin with, the old Foam Strip was attached to the door insulation and not the door. The attempt to remove the old Foam Strip from the insulation became cumbersome, so I just attached the new Foam Strip on top of the old Foam Strip. So far, after a few cycles, it appears that it corrected the leak.

Once I got the door open, I removed the door cover screws with a Torx driver, where I found the broken handle and the Latch Assembly. One of the plastic handle pivot points had broken clean off. In my Brilliance, I went online to PartSelect, found that the part that I needed had been discontinued (from Maytag) and picked one that looked right. It ended up being the assembly without the handle, the part I needed. Save yourself some time and call the 800 number to make sure you get what you need. They were very helpfull in returning the wrong part to get the right one. Once I had the part, the repair was very straightforward. I just had to open the door up again, swap in the new Latch Assembly with the steel reinforced pivot point handle, and put the screws back in the door. The latch assembly is held in place by two of the door screws. Watch the cut off switches on the assembly, the power is hot until you power off the circut at the electric panel.

Simply popped the new cover in. My part by the way was really easy to identify on the website, easy to order and arrived in a very timley fashion!

Being a fairly technical female, I decided after Internet research to replace this part by myself. It could not have been easier - even after reading several Internet horror stories. I believe the major difference being I replaced the entire assembly, not simply the latch.

You need a hex-head allen wrench to remove the inside cover of the dishwasher door, and some sort of pliers to remove the old unit. I used vice grips since I am a wimpy girl - they worked nicely (this took the longest time).

Step by Step:

Turn off the power to your dishwasher.

Remove the door screws and carefully lift it to access the door latch assembly.

Remove the old door latch by unplugging the black and white electrical mechanism. Pay close attention to which side the black and white connections are removed from for reconnection reasons. This is where I had to use vice grips. It took a bit to "unplug" the old latch assembly.

Once the old latch assembly is removed, position the new latch assembly and reconnect the electrical source.

Carefully reposition the door and replace the screws.

Turn on the power.

Run a short cycle (I used rinse) to make sure that the unit was replaced correctly.

Can it be any easier than that??

The real cause of the leak had nothing to do with the foam strip. The latch for the front loading door at the top needed to be adjusted to hold the door in tighter to the rubber door seal. This simple adjustment stopped the leak but since the foam seal was all encrusted with dried detergent from probably years of absorbing the leak, I replaced it with your new foam strip. I used a screw driver with torx bit and removed the stainless screws holding the inner door to the outer door. Once these were separated I removed the old foam strip using a putty knife and lacquer thinner. Placing the new strip onto these cleaned surfaces was the easiest part of the whole repair.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Turned off water and power to the unit. Removed kick plate from under the dishwasher to access the water contol valve. Placed an absorbant rag under the water valve and water line. Disconnected solenoid on water control valve from electrical connection with my fingers. Used a standard adjustable wrench to disconnect the water line from the water control valve. Then used a 1/4" nut driver to loosen the two bolts that hold the water control valve on to the mounting bracket. Pulled the water control valve slightly forward to disconnect the water feed line to the dishwasher. Used a blunt end plier to pinch the clamp open and slowly wiggle the feed line off of the water control valve. Then removed 90 degree elbow off of the water control valve and used pipe dope and connected the elbow onto the new water control valve. Replaced water control valve in reverse order and utilized new hose clamp to reconnect feed line to new water control valve. Saved door seal for future use, when seal goes bad.

1st: Unscrewed the inside of the door (actually hex screwdriver needed).
2nd: Removed broken part (one side of handle latch (which is plastic) was broken.
3rd. Had to disconnect two electrodes that were attached to the part that held the handle (there are two small prongs that you need to push back to remove these)
4th. In order to place the handle on the groove, you need to pull apart the bottom of the housing piece (it looks like it would be a hinge, but you just pull it apart)
NOTE: Make sure you have another person hold the top portion when you pull this apart because it has a spring and will come completly apart. This happened to us and it was a pain to get it back together.
5th: place the smaller "clamps" plastic pieces in the grove and then it should slide down into the groove, which will also seat the outer "plastic clamps" into the grooves.
NOTE: It seems like the repair part was built to reinforce this part of the handle, since this was the part that broke before. It is now reinforced with a little metal rod on each side.
6th: After all that, you need to place the two electrodes back on the piece.
7th: Hold it in place and put the inside of the door back on (start a screw on one side and then go to the opposite side. This will help to align the screw holes).
8th: After I put it all back together, I turned it on to make sure it worked ok.