ADB1500AWS41 Amana Dishwasher - Instructions

Ensure to order part # PS1559543, which is the complete assembly although the diagram doesn't show this, and not PS2100626 which doesn't include the handle. The new assembly is a different style than the original therefore you should replace the complete assembly.

This was an easy fix. Remove the eleven torque screws on the door and separate the inner door panel enough to remove the old assembly. Remove the wire connections from the door switches, reconnect to the new assembly, and reinstall the assembly and inner door panel.

First I removed the screws from the inside of the door exposing the latch assembly. Removed the old part and installed the new assembly. Don't screw it on to the door untill the cover is on again.
First I ordered only the latch without the handle. Found after opening it up the handle was broken on the inside so had to order the assembly. It's a piece of cake to install. If you're having touble opening the door don't think because the handle looks ok from the outside it's not broken.. probably is. Partselect.com is the greatest company to deal with. I'd recommend them to anyone and have.
Sam

Turned off water at the shutoff valve. I did not turn off the power, but it is recommended you do so. I pulled the dishwasher out from under the cabinet and used a car jack to lift the front off of the ground. Disconnected the water supply and the rubber hose that fills the dishwasher tub. There are two 7mm screws that hold the water pump to the frame. If you do not have a 7mm socket, the easiest thing to use is an interchangeable screwdriver. When the screw bit is pulled out, the empty screwdriver is a 7mm. Used adjustable wrench to remove the brass water port for the supply line. Teflon tape to all connections and hooked everything back up. My supply line was old and was leaking, so I had to run out and get a new one, so that added about 30 minutes to what would have been maybe a 20 minute repair.

Removed the old one....slid in the new one.

I removed the screws around the top and halfway down the sides of the inside of the door. I found that you dont have to remove all 10 screws to access the assembly. Reach in and pulled out the assembly, there was enough slack to pull it out above the door. Pull the connectors off and slide the new ones on. Set the new assembly back in place, insert the 2 top screws first, and then the rest. That was it...very simple to change.

UNSCREWED THE LOWER PART BY PLIERS AND HAND. COULDN'T UNDERSTAND WHY THE LOWER
PART WAS AVAILABLE BUT THE UPPER SPRAY ARM
WAS NO LONGER AVAILABLE WHEN THEY BOTH GO TOGETHER..

simply pulled out old one slowly inserted new one (stretching slightly) Presto done

I had to remove the the old retainer from the old wash arm ,install it on the new arm by snapping it on then I snapped the arm with the retainer up top of dishwasher.

Easy! Unscrewed panel, took off old latch, put on new. Took about five minutes.

I pulled out the dishwasher enough to tip it back and put a block of wood underneath the front leveling foot.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.

After disassembling accumulator assembly looking for reasons that washer not washing properly, I noticed accumulator filter had failed. The plastic (or whatever material it is) covering the holes was torn in a couple of different holes. Realizing that this was not the reason for the loss of pressure I investigated a little more and found that water arm going into the docking station was extremely worn with much play. Water pressure was compromised because of it. I replaced filter and docking station and now its like a new dishwasher again. Saved a dishwasher from the landfill!

Dishwasher is in our summer cabin in Colorado so everything has to be drained for the winter. Not really sure whether this leak was freeze caused or that the valve was just old. Couldn't find a crack when I got the old one apart; might have been just an O ring needed. Anyway, just follow the video provided by this site for replacement of the valve; really easy. Biggest hassle for us was getting the dishwasher out (and back in) as it was wrapped in insulation which made the fit really tight. Thought I had everything I needed when I started but didn't have teflon tape which is needed for the brass fitting connecting the water supply to the valve (fitting is in your old valve and will be reused with the new one).

1. Shut off water supply

- Remove water line and drain hose if you need to. I was able to simply move the dishwasher forward some to do this repair without disconnecting

2. Remove access panels on the bottom.
3. Open the door
4. Remove Door Gasket carefully (do not stretch)
5. Use torque 20 driver to remove 6 screws that were under the gasket

- Some of the screws were rusted for me so I had to use kroil, a pick to clean out rust, and a hammer to help get the torque driver in enough to remove the screws. A local hardware store had replacements.

6. Use Phillips screwdriver to remove screws holding mounting brackets
7. Carefully move dishwasher out some (Careful if you have a copper water hose you may want to disconnect it)
8. Remove the strike if it is attached above the metal bar
9. Lift the metal bar and push down on the tub to make room to remove the old mounting brackets (slide them up, forward, and to the side)
10. Put new mounting brackets in place (put mounting bracket under bar, slide over into place)
11. Reverse the order at this point.

Be careful not to stretch the gasket. I soaked mine in vinegar for a bit and gently washed with dish soap to remove deposits.

The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 bucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.

followed video provided,simple job and cured problem