ADB2500AWS2 Amana Dishwasher - Instructions

PartSelect web-page for this model listed the handle as the most often ordered part. It arrived the next day after the order. It was necessary to remove about a dozen Torx screws to remove the back from the door. The power was turned off at the breaker. Two electrical fittings were removed from the broken handle and placed on the new one, and the part was put into position and the door back screws reinserted. I was fortunate to have the appropriate Torx driver and suggest that PartSelect offer such an unusual tool with the part.

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

Removed inside door panel, handle assembly was then free to move. Unpluged both switches attached to handle assembly. Plugged in new switches and positioned new handle assembly. Replaced inside door panel and screwed into place. Closed door. it works. job done.

Luckily the door opened one last time. Remove torx screws on the inside. Spread panel open to gain access to handle. Removed handle because it's already loose from removing torx screws for panel. Electrical wire connectors were extremely tight. Used pliers to remove connections there are 2.
Reverse procedure for installation.

First, I had to purchase a small socket set that had the piece needed to remove the screws from the inside panel of the dishwasher. I didn't cost much. After removing the screws, I disconnected the old door latch/handle, but had to leave the old leads in place because I couldn't remove them. I replaced the old latch/handle with the new one, replaced the inside panel, and tried it out. The new latch/handle worked great. The replacement time was under 20 minutes (struggling with the old leads). Very happy with the outcome, though.

Thanks.

I removed the screws from the inside of the dishwasher door and removed the handle. You have to unplug the handle from the door assembly. When I got the new part I plugged in the two plugs, aligned the cover of the door and replaced the screws. It works great and it was super easy!

No repair needed, just inserted the new dishrack. My only complaint is the lack of upright tongs in half of the rear section of the rack. This limits the number of dishes that can be stored. My original rack had tongs in all areas which better suited my needs. If there is a replacement that better suits my needs I would like an exchange.

1. Remove both upper and lower dish trays
2. Remove the “Spinner /Sprayer” (small nut on the top)
3. Unclip the “Tower” from the top and rear clip
4. Remove the “Tower” from the unit
5. Remove the “Filter Guard” on the bottom by removing 3 torx screws
6. Remove the “Discharge Housing” & “Impeller” (1 – 15 torx screw)
7. Remove and replace the “Accumulator Filter” (8 – 20 torx screws)
8. Assemble in reverse order

Shut off the electricity to the dishwasher. I removed all 11 screws from the door panel. After separating the 2 door panels, I removed the 2 door switches from the door handle ( I used a flat head screw driver to help get them out). Then I unplugged the 2 switches and plugged in the new ones. I replaced the door switches into the door handle ( this was not an exact fit because the new switches is slightly larger than the old ones). I put the new switches in place as tight as I could in the handle. I screwed the 2 screws holding the handle first to secure it before I put all the other screws in the door panel. I turned the electricity to the dishwasher back on. Our dishwasher has been working perfect ever since then and it is over 10 years old.

Open front removed all the star screws. Took the old switch unplugged the wiring one at a time to put on new switches. Placed the new switch back and installed all screws. Using a drill with the star tool made it go faster. Total time 9 mins

I found this website and it easily helped me find the part needed. I ordered it using standard shipping and it arrived the next day!! After reading a few hints like taking note how you plug it back in I installed the part and it was back up and running. Easy and quick, thank you part select!!

Pulled out the old one and put in the new one!

I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.

replaced rack

I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws.
I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.