ADB2500AWS2 Amana Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from Owego, NY
- Parts Used:
- 99002753
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top washer arm kept falling off
Snapped out the old retainer, snapped in the new. Then snapped in the washer arm. Done. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Overland Park, KS
- Parts Used:
- 99002588
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
humidity would seep out absorbing into the granite above
remove old seal, put in new - my 10 yr old could do it. Note - there is a white mark on the back of the seal indicating the middle so you can line it up when installing the new seal - makes it easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Chester Springs, PA
- Parts Used:
- 99002588
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher leak from door seal
Door gasket fit in like a champ! No special tools required - just scissors to trim off the excess ends. Unfortunately this didn't correct the leak. The leak was caused by a Home Inspector who ran the dishwasher without soap. The soap has a defoamer in it. If you run the dishwasher without soap the water mixes with the surfactant in the jet dry and causes foam which results in a door leak. The foam also causes the pump to cavitate which is not healthy for the pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROY from MERKEL, TX
- Parts Used:
- W10202535
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Water would not go to dishwashe
Took the dishwaher apart. Found out the float was damaged. Replaced the float and the float switch. Put back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Simon from North Syracuse, NY
- Parts Used:
- W10862259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken handle
Easiest repair ever! 11 sized T20 screws hold the plastic to the door. Remove those and the handle just sits there. Disconnect the leads from the old and attach to the new. Total repair time under 10 minutes, and I'm NOT a handy guy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Akron, OH
- Parts Used:
- W10862259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door handle
In less than 5 minutes we took the screws out, fixed the latch and had it back together again. The amazing part of the story is the perfect diagrams and helpful instructions from Part Select. I ordered the part one day and by noon the next day the dishwasher was fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from Prince George, VA
- Parts Used:
- W10862259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
handle was broken and door wouldn't open unless pried
removed the screws that held the inner panel. removed the handle from its electrical connectors (2) reinstalled new unit and works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Foothill Ranch, CA
- Parts Used:
- W10862259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken latch
Latch assembly came in a matter of days. Screwed it in and voila! good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from camas, WA
- Parts Used:
- WPW10192799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishes not getting clean. Tear in the filter.
Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Gardner, KS
- Parts Used:
- 6-917696
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher Stainless Steel Face Panel
Wanted to change our dishwasher to a stainless steel appearance. When the panel was delivered in 1 day I might add it was flawless. I removed the old panel and the new panel attached to the dishwasher perfectly with the screw holes exactly lining up. The most inexpensive way to turn a kitchen into a stainless steel appliance look.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from henderson, NV
- Parts Used:
- WP99003317
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
detergent dispenser door latch not holding
from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Burlington, MA
- Parts Used:
- W10283681
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher was leaking do to heating element decay.
1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Amarillo, TX
- Parts Used:
- WP99002751
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
START LIGHT WOULD JUST BLINK AND WOULD NOT DRAIN, JUST BLINK
Switch was not the same switch as what was in the unit, similar but switch was normally closed instead of open, so had to take the switch apart and change sides with the contacts! should be the same, but was not, so in the end worked fine after an adjustment!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eva from columbus, OH
- Parts Used:
- WPW10192799
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
accumulator filter
Unfortunately, my experience was unlike that of the other people who posted. While everything did go back together it was very difficult to get it all to press down tightly enough to tighten each set of screws. The project took about 2.5 hrs and I still don't think it is exactly right. I'm still going to have a professional out to finish the job. Also, the tool needed to complete the job was nothing fancy, but also not in everyone's home tool kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from Sabetha, KS
- Parts Used:
- W10862259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Latch on dishwasher door would not function.
Simply unscrewed the door and plugged in the new parts. Very quick, very easy, saved us hundreds on a new dishwasher.
Was this instruction helpful to you?
Thank you for voting!