ADB3500AWW1 Amana Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ron from Lexington, OK
- Parts Used:
- 6-917696
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Install stainlees steel front on Dishwasher.
Remove screws holding the existing white panel. Once that panel was loose, there are several screws internally that have to be taken out in order to fully remove the panel. The new panel is then installed by putting it in place and reinserting the screws. It is an easy"fix" to change the DW to match other stainless steel appliances. You do need to be careful to make sure the door springs stay attached.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Billings, MT
- Parts Used:
- WP6-917647
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishes were not getting clean on the top rack.
The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Pickerington, OH
- Parts Used:
- WP6-917647
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cups and glasses on upper rack were not getting clean.
Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.
The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.
The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vanessa from Germantown, MD
- Parts Used:
- 99003429
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing disherwasher flatware basket
No repairs needed other than opening the box and placing into dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Philadelphia, PA
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Latch Asembly Broke, Door wouldn't close properly
The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelley from Burlington, IA
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Latch Assembly
I removed the screws around the top and halfway down the sides of the inside of the door. I found that you dont have to remove all 10 screws to access the assembly. Reach in and pulled out the assembly, there was enough slack to pull it out above the door. Pull the connectors off and slide the new ones on. Set the new assembly back in place, insert the 2 top screws first, and then the rest. That was it...very simple to change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francine from Bristol, CT
- Parts Used:
- WP6-917644
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Top wash arm kept falling off.
I had to remove the the old retainer from the old wash arm ,install it on the new arm by snapping it on then I snapped the arm with the retainer up top of dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Chester, NH
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not shut
Easy! Unscrewed panel, took off old latch, put on new. Took about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from BLUE SPRINGS, MO
- Parts Used:
- WP6-917644, WP6-917642
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
WAS NOT GETTING DISHES CLEAN
UNSCREWED THE LOWER PART BY PLIERS AND HAND. COULDN'T UNDERSTAND WHY THE LOWER
PART WAS AVAILABLE BUT THE UPPER SPRAY ARM
WAS NO LONGER AVAILABLE WHEN THEY BOTH GO TOGETHER..
PART WAS AVAILABLE BUT THE UPPER SPRAY ARM
WAS NO LONGER AVAILABLE WHEN THEY BOTH GO TOGETHER..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert d from MOORHEAD, MN
- Parts Used:
- WPW10275768
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door didn't seal tight. So when it would go into rinse mode it would leak water on my floor
The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 bucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karen from escondido, CA
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken handle
First I removed the screws from the inside of the door exposing the latch assembly. Removed the old part and installed the new assembly. Don't screw it on to the door untill the cover is on again.
First I ordered only the latch without the handle. Found after opening it up the handle was broken on the inside so had to order the assembly. It's a piece of cake to install. If you're having touble opening the door don't think because the handle looks ok from the outside it's not broken.. probably is. Partselect.com is the greatest company to deal with. I'd recommend them to anyone and have.
Sam
First I ordered only the latch without the handle. Found after opening it up the handle was broken on the inside so had to order the assembly. It's a piece of cake to install. If you're having touble opening the door don't think because the handle looks ok from the outside it's not broken.. probably is. Partselect.com is the greatest company to deal with. I'd recommend them to anyone and have.
Sam
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lance from Duvall, WA
- Parts Used:
- 99002624
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
old wash arm was cracked and had gunk in it.
The upper arm assembly removes easily by unsnapping a plastic part or two that holds it in place.
Once the arm assembly is removed, you simply remove the screw that holds the arm on, replace the arm, and replace the screw. The key thing here is that you need a "star drive". This is a screw driver or bit that has a star shaped end. I don't know what size it is.
Once the arm assembly is removed, you simply remove the screw that holds the arm on, replace the arm, and replace the screw. The key thing here is that you need a "star drive". This is a screw driver or bit that has a star shaped end. I don't know what size it is.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Bloomington, IL
- Parts Used:
- 99002780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken wheels on dishwasher racks
The plastic wheels on the upper and lower racks keep breaking. The latest casualty was also chewed up by the dog(s). They just pop right on the posts, a simple 2-second fix. I ordered the parts on a Tuesday morning, standard shipping, and they arrived FedEx less than 24 hours later. They came from Peoria, and I live about 1 hour away in Bloomington. Very pleased with the service. Will order from PartsSelect again if I need parts for any other appliance that I can fix myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Darien, IL
- Parts Used:
- 99002780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower diswasher tray missing 3 wheels
All I had to do was litterally snap the wheels into place..it was so easy and so cheap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from CRESTWOOD, IL
- Parts Used:
- WP99003147
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper rack front guide wheels had worn completely and would slip out of the guide rail
Replacement parts were an exact match so overall it was pretty simple. At the front end of the rack guide rail there is a removable stop. After removing the stop the old guide wheels can be removed from their "axles" (actually a part of the wire rack is bent at 90 deg to act as an axle), and simply moved forward and out of the guide rail. Took a few minutes to clean the guide rail, then installed the new guide wheels and pressed the removable stop back into place. Works like new.
Was this instruction helpful to you?
Thank you for voting!