ADB3500AWQ36 Amana Dishwasher - Instructions

After receiving the latch assembly, which arrived rather quickly, I found the handle itself was not enclosed in the package. Therefore this repair was delayed and after several calls to the 1-800 number I was informed the company had discontinued the distrubution of the handle. They offered a full refund, however I'm still waiting for the return labels so as to ship the latch back.

Now on the brighter side, the company representative put me in touch with a local distributor that did carry the latch/handle assembly as one piece and for a lot less money.

For those who are attempting the repair, don't worry, It was very simple. Just remove hex screws, lift the inside panel, unplug the two connectors and insert the new assemply.

Must say my wife was very happy to have the dishwasher up and running again.

Good luck !

Turned off water at the shutoff valve. I did not turn off the power, but it is recommended you do so. I pulled the dishwasher out from under the cabinet and used a car jack to lift the front off of the ground. Disconnected the water supply and the rubber hose that fills the dishwasher tub. There are two 7mm screws that hold the water pump to the frame. If you do not have a 7mm socket, the easiest thing to use is an interchangeable screwdriver. When the screw bit is pulled out, the empty screwdriver is a 7mm. Used adjustable wrench to remove the brass water port for the supply line. Teflon tape to all connections and hooked everything back up. My supply line was old and was leaking, so I had to run out and get a new one, so that added about 30 minutes to what would have been maybe a 20 minute repair.

The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 bucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.

I removed the screws around the top and halfway down the sides of the inside of the door. I found that you dont have to remove all 10 screws to access the assembly. Reach in and pulled out the assembly, there was enough slack to pull it out above the door. Pull the connectors off and slide the new ones on. Set the new assembly back in place, insert the 2 top screws first, and then the rest. That was it...very simple to change.

I had to remove the the old retainer from the old wash arm ,install it on the new arm by snapping it on then I snapped the arm with the retainer up top of dishwasher.

Removed the old one....slid in the new one.

UNSCREWED THE LOWER PART BY PLIERS AND HAND. COULDN'T UNDERSTAND WHY THE LOWER
PART WAS AVAILABLE BUT THE UPPER SPRAY ARM
WAS NO LONGER AVAILABLE WHEN THEY BOTH GO TOGETHER..

Slipped it on the upper rail.

Easy! Unscrewed panel, took off old latch, put on new. Took about five minutes.

first, i removed the inner door panel exposing the latch assembly. i then disconnected the wiring to switches noting their locations. removed and replaced with new latch assembly, connected all wiring back to their corresponding switches, assembled the inner door panel and checked to make sure the latch was working properly.

Ensure to order part # PS1559543, which is the complete assembly although the diagram doesn't show this, and not PS2100626 which doesn't include the handle. The new assembly is a different style than the original therefore you should replace the complete assembly.

This was an easy fix. Remove the eleven torque screws on the door and separate the inner door panel enough to remove the old assembly. Remove the wire connections from the door switches, reconnect to the new assembly, and reinstall the assembly and inner door panel.

First, shut off the circuit that the dishwasher is on. Remove the 10 - 12 screws that secures the inside waterproof panel to the door. There are two electrical connections are either side of the handle (latch assembly) that need to be removed. No need to disconnect any other connections or reservoirs. The handle comes right out. Seat the new one in door front opening. Reconnect the electrical leads and reseat the interior panel. I would put in the 2 screws are either side of the handle first; then the 2 at the bottom on either side and then the remaining. This is a very easy DIY job.

After only 2 years, the Amana dishwasher door began to stick severely. If finally stuck so bad that I had to break the handle to get the door open. The replacement latch and handle fit perfectly and it only took a few minutes to get the screws off of the inner door panel to access the broken latch.

Removed all the screws holding the inside panel of the door to the door itself. Lifted out the old broken door latch. Pulled the wire clips from the 2 switches located on either side if the door Latch assembly. This is a bit difficult. You have to keep working the wire clips back & forth; Up & down until the clips are free from the switch metal contacts. Reinstall the wire clips on the new door Latch assembly making sure you attach the black wires and white wires on the same side of the new latch assembly as on the one removed. Replace the new latch assembly aligning the mounting holes on the door with the new latch holes. Replace the inside panel aligning the holes and replace the screws. The screws were the star head type so you need a special driver bit. I used the box the latch came in the prop up the inside door panel while I worked.

First I removed the screws from the inside of the door exposing the latch assembly. Removed the old part and installed the new assembly. Don't screw it on to the door untill the cover is on again.
First I ordered only the latch without the handle. Found after opening it up the handle was broken on the inside so had to order the assembly. It's a piece of cake to install. If you're having touble opening the door don't think because the handle looks ok from the outside it's not broken.. probably is. Partselect.com is the greatest company to deal with. I'd recommend them to anyone and have.
Sam