DDW361RAW Amana Dishwasher - Instructions

I first removed both lower front shields,(4 screws)
I then shut off water supply to inlet valve from hot water supply. I removed the water hose from inlet valve,two electrical terminals,( I put tape on right side terminal and lettered with an R as not to mix up the two terminals)removed the hose clamp,removed valve from frame.I reinstalled in reverse procedure.I turned the water back on and checked for leaks.I started the normal cycle and water flowed into the dishwasher as designed.

The rack assembly was not altogether assembled. Had to remove one part from the old one and reassemble on the new. Also, The racks that make place for a bowl instead of plates was not assembled.

I went to take the bottom front panel off and ended up dropping the screw down behind the baseboard and then found that I did not need to take the panel off. The broken end of the float was not obstructing and I was able to just drop the new float in place. I spent more time looking for a replacement screw than any thing else. Ran it and it works fine.

I first removed the bottom access panel and 2 upper screws holding the dishwasher to the counter. Be sure to remove the standing water in the bottom tray. I pulled the chassis far enough forward to reach where the top shower hose attaches ( the supply line and wire had enough slack to move the chassis ). Not knowing how the rotating shower arm attached, I unscrewed the ribbed retaining ring above it, and found the whole assembly came loose - freeing the upper end of the shower hose. Put a shallow tray under the lower end of the shower hose to catch the remaining water and loosen the hose clamp to free the remaining end of the hose. Transfer the rubber washer at the top end and the hose clamp at the bottom, to the new hose and install. A quick repair, but one that shouldn't be needed on a 4 year old dishwasher.

I followed instructions of others that were posted. Door seal was simply removing old seal, cleaning track and pushing new seal in,making sure it was even all around. Removing the door cover to get at the Dispenser grommet was simply removing all 7 hex nut screws. Had to go out and buy the proper hex nut screwdriver . I did not remove the wiring, just turned cover over to remove the two nuts holding the dispenser. The nut on the left was a little hard to get off, had to kind of force the socket onto the nut. Otherwise all went well and simply removed the old grommet and installed new one. Finding the right tools was the part that took the longest. I had hard water before putting in a water softener so that was probably hard on the seals plus the machine was an older model. No problems now and saved having someone come in and do a repair.

first I turned off the water to the dishwasher, and turned the power off for the dishwasher.
removed the 4 screws from bottom panel
then removed the 2 screws from the bottom of the counter,
at this point I could pull the dishwasher out. then figured out where the part went and attached.
pushed the dishwasher back and lined up the holes under the counter, put those in first, the put the bottom panel back on, turned the water back on, and flipped the breaker switch.
Reading the other stories really did help me get some idea of what needed to be done

The problem was the rubber end on the upper shower head pipe at the pump. Not to hard . Slide dishwaser half way ouy the ptpe is on the right side.The bottom end is is just a clamp the top drops in from the top, inside there is a nut above the upper shower head. You can unsrew the nut with your fingers, it is right above the upper shower head.There it a washer at the top of the pipe that should be replaced that doesnot come with the pipe

Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

Removed 7 Torx Screws ... removed inner door panel ... snapped off the selinoid after noting the exact original position ... removed the Latch assembly 2 hex head screws ... removed the old Grommet which was crumbling apart ... stretched the new grommet in place. Then did the steps in reverse to complete a successful repair.
Thanks to your website, quick turn-around service and customer's repair stories, I probably saved a few dollars but mostly, I realized how much I love my dishwasher now more than ever!

First I replaced the soap door grommet -- door still leaked. Then I went for the really expensive part ($40) -- the door gasket. The old one came right out and the new one went right in -- 15 minutes tops -- and the door no longer leaked.

Thanks to all the previous posters for their hints.

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

I removed the screws holding on the interior door panel. This exposed the soap dispenser latch mechanism. After removing the two retaining screws I transferred the original parts to the new retainer and replaced the grommet prior to reinstallation of the mechanism and interior door panel. A savings of probably $100.00 or more for a service call and parts. Should last a few more years.

Both racks are just roll out & roll new racks back in, no tools. Racks came in just 2 days, one was damaged in transit. Called to advise PartSelect of the problem. replacement rack was here within 2 days.
Great service. Jack

Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.

The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.

Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.