ADB1500AWQ10 Amana Dishwasher - Instructions

The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.

Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.

The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.

No repairs needed other than opening the box and placing into dishwasher.

A really easy and simple repair that required no tools. The parts were delivered within a matter of days. Completely satisfied with transaction and results.

I had to remove the the old retainer from the old wash arm ,install it on the new arm by snapping it on then I snapped the arm with the retainer up top of dishwasher.

Easy! Unscrewed panel, took off old latch, put on new. Took about five minutes.

UNSCREWED THE LOWER PART BY PLIERS AND HAND. COULDN'T UNDERSTAND WHY THE LOWER
PART WAS AVAILABLE BUT THE UPPER SPRAY ARM
WAS NO LONGER AVAILABLE WHEN THEY BOTH GO TOGETHER..

The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 bucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.

Removed the old part, which just snapped into place, replaced it with the new part that was sent by your company. Unfortunately, when the new part was plugged into the correct spot, it would not stop running. So all water that went into the dishwasher was pumped right back out. So obviously there must have been an addition issue with the dishwasher.

Removed screws. New Part does not come as an assy. Need to order handle. Other sights offer full assy for less.

first, i removed the inner door panel exposing the latch assembly. i then disconnected the wiring to switches noting their locations. removed and replaced with new latch assembly, connected all wiring back to their corresponding switches, assembled the inner door panel and checked to make sure the latch was working properly.

Turned off water at the shutoff valve. I did not turn off the power, but it is recommended you do so. I pulled the dishwasher out from under the cabinet and used a car jack to lift the front off of the ground. Disconnected the water supply and the rubber hose that fills the dishwasher tub. There are two 7mm screws that hold the water pump to the frame. If you do not have a 7mm socket, the easiest thing to use is an interchangeable screwdriver. When the screw bit is pulled out, the empty screwdriver is a 7mm. Used adjustable wrench to remove the brass water port for the supply line. Teflon tape to all connections and hooked everything back up. My supply line was old and was leaking, so I had to run out and get a new one, so that added about 30 minutes to what would have been maybe a 20 minute repair.

Ensure to order part # PS1559543, which is the complete assembly although the diagram doesn't show this, and not PS2100626 which doesn't include the handle. The new assembly is a different style than the original therefore you should replace the complete assembly.

This was an easy fix. Remove the eleven torque screws on the door and separate the inner door panel enough to remove the old assembly. Remove the wire connections from the door switches, reconnect to the new assembly, and reinstall the assembly and inner door panel.

First, shut off the circuit that the dishwasher is on. Remove the 10 - 12 screws that secures the inside waterproof panel to the door. There are two electrical connections are either side of the handle (latch assembly) that need to be removed. No need to disconnect any other connections or reservoirs. The handle comes right out. Seat the new one in door front opening. Reconnect the electrical leads and reseat the interior panel. I would put in the 2 screws are either side of the handle first; then the 2 at the bottom on either side and then the remaining. This is a very easy DIY job.

I'm telling this story for my husband who is a pretty handy guy--I watched him do the repair. I had had someone out to look at the dishwasher and they said it would be $284 to fix this one little thing because you couldn't buy the one little part separately, you had to buy a whole new motor. Since the dishwasher is old, it didn't make sense to invest this much in it--might as well buy a new one for that kind of money. My husband did some looking around and found the part on your site and installed it himself. So the cost was under $40. The dishwasher is now working better than it had been for a while.