ADB2200AWS Amana Dishwasher - Instructions

Ist Repaired a hole in a rubber hose under the sink. 2nd Removed the 10 foot drainage hose with a regular screw driver (1 clamp at each end of the hose).
3rd Removed the insulation and replaced with the new after disinfecting the entire top and sides of the dishwasher with bleach. This eliminated all bad odor etc. only had to remove 2 plastic brads, 1 on each side of the unit.

Done and no leaks.

First I read all the reports for not cleaning properly already listed on this site. I had to replace the docking station with flappers. When I removed the station I lost the flappers down the water delivery tube just like Jon said I would in his repair post so I removed the water distribution assembly fished out the old flappers and snapped in the new.
But then I figured I might as well check out the accumulator while I was in the tub anyway - I had read that you need Torx screwdriver bit, which I had, undid the screws, pulled out the accumulator screen which was about 80% clogged, discovered I need a new chopper blade and my impeller is disintegrating, put it back together and lost ten minutes looking for the three screws I had incorrectly put in too soon, and now it is cleaning a packed full load like it was supposed to do.
**I love this site - I went to the virtual repairman and it listed every problem I had with this appliance in the order they happened (door latch broke years ago). - I think I am going to look up stuff that I own so I will know ahead what could go wrong with them.

And absolutely NO DUCT TAPE was used in this repair.

The spring mechanism is on the side, so you have to pull the dishwasher out onto the floor. To do that, you have to remove the floor molding (preferably without breaking it) and remove the base coverings (painted metal plates on the bottom of the washer. Unscrew the side gasket plates on the side of the dishwasher (just inside of the door) where it attaches to the cabinet and the screws in the braces at the top (inside the door) where it attaches to the counter top. Now you will be able to slide the washer forward to look at the sides where the door springs are. Depending on the floor, you may have to raise the washer's front feet. They screw up. As you pull the washer forward be careful to not mess up the insulation which drapes over the top and sides. You only need to come out 1/3 of the way to see the sides where there is a plastic wheel at the forward bottom corner. As you move the door up and down you can see the hook where the cable goes and further up the side you can see several notches where the spring goes. Hook the cable and bring it around the wheel and attach it to the spring. To reinstall, just follow these directions backwards. Good luck.

I wanted to get the dishwasher cleaning better and thought that maybe the accumulator needed to be replaced. I figured that I'd swap out all the spray arms as well, just for good measure.

I needed Torx screwdrivers (T15 and T20, I think - not 100% sure on that) and patience because there's really quite a lot of screws to get the accumulator out. Finally got to it and it didn't look damaged, but replaced it anyway.

The spray arms are easy - they just snap in except for the lowest one, that had a plastic nut. I ordered a replacement nut just in case I broke this one (you know how that goes) taking it off. Well, it took pliers, but it came off ok.

In the end, my dishwasher is happy and cleans much better now.

After finding out that the impeller shaft was stripped (plastic) I quickly found the correct replacement on partselect.com by using my model number.
You do not have to remove the dishwasher, if you know what is wrong. But, throw the breaker switch and turn off the water! After removing the spin washer arm, Undo all of the torx screws and pull out the plastic filter looking plates along with the center plastic water jet. This jet provides water for the upper washer assembly. You may have to pop that upper assembly out to protect it from damage.
The black impeller should just pull out if the plastic shaft is stripped. Otherwise, unscrew the small torx head and remove the impeller. You can remove the blade at this time and unscrew the plastic shaft by unthreading it while keeping the motor from spinning. (I shoved a screw driver underneath the dishwasher through the motor. Also the motor is just floating on the rubber gasket and can easily pulled out to accomplish this task. It's heavy and has a plug attached to it. You'll see where you can shove the screw driver. This comes in handy while installing the new shaft, because it is metal. Which is a great, long awaited upgrade for the Maytag Quiet Series. Once you find which shaft to use, (which correct inner thread, course or fine), install it with the great directions that come with the part. Putting all the stuff together is not as bad as one would think, there is only one way for it to go back together. After installation is complete, turn water and breaker switch back on. Run a cycle and listen for the washing cycle against the wall of the washer. If you cannot tell the difference, you can unscrew the white lock arm and insert it into the door. Turn it on and watch how a dishwasher works. Get ready to get a little wet. Towels!

The original brackets that hold the water distribution manifold to the back and top of the tub came off the "X-shaped" plastic posts on the tub walls. That caused the upper wash arm to sag down into the travel of the upper dish rack and was broken off when the rack was pushed in.
I bought 2 new brackets and a new wash arm. The new brackets had a smaller aperature than the originals and fit tightly onto the plastic posts, holding the manifold firmly in its proper location. Replacement of the brackets and the new wash arm took less than ten minutes and required no tools!

Not being very computer literate, the most difficult part of the entire venture was navigating your web site. But I finally found the part I needed. I paid on line with a credit card, and received the part within a few days. I popped it in the dishwasher, and it took three days before my son noticed it.
He was surprised and I was proud to say " I ordered it on line."
All's well that end's well.
I would difinately use your service again.

I unscrewed the door panel. removed the plastic cover protecting the dispenser. unscrewed the dispenser (6 screws). I removed the old dispenser and put the new one on and put it all back together. It was pretty easy.

disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes

Unpluged the electric, Disconnected the water line and the drain line. Removed the dishwasher. Removed and installed the new water inlet valve and the float switch. This was a very simple repair. Reinstalled the dishwasher and connect
the water and drain line. Pluged in the power line. Turned the dishwasher on and it worked perfect. Thank you for the correct parts.

This isn't a how to fix it....it's what part was bad. I had originally contacted the local Maytag repair center and the owner swore up and down that our problem had to be the thermostat and not the heater. He said he had only replaced maybe 5 heaters in 15 years. But our heater looked like heck, with hard water deposits and all, and it wasn't that old, but we went ahead and ordered the thermostat from PartSelect, which came in a day. The problem wasn't the thermostat, so we ordered the heater from PartSelect (again, only one day delivery) and our dishwasher is working again. The heater coil actually had a hole in it from some sort of corrosion. My 18-year-old son did the repair job in a jiffy.

First replaced rubber seal around door, which did not stop the leaking.
Then ordered insulation foam strip and replaced old one, which fixed problem. Put new strip over the old one because tub was slightly warped.
Very pleased with order speed and cost.

All that was broken on the old detergent dispenser was the door but the door can not be ordered without buying the whole detergent/rinse aid assembly. When I got the new item I just removed the old door and replaced it with the new door that I had taken off the new one. I still have the new detergent/rinse aid assembly that I can keep if I need to change it in the future.

After replacing the door gasket and seeing that this wasn't the problem, using the schematics found at partselect.com I finally realized that it may be the insulation foam strip. I ordered the product and received it very quickly. Installation went fairly quickly. It was easy to remove the old foam strip and install the new one. The only problem was that the foam strip was about 1/4 " too short and it didn't cover the entire bottom. I improvised a little bit and cut off some of the old strip and covered the gap. So far the leak seems to have been fixed. In addition to the foam strip I had to buy a torx screwdriver for $11 at the local hardware store. The total spent was around $25.

After examining the door and main seal around the dishwasher I thought everything looked okay. I looked online to order a new seal anyway and discovered from others that the leak was probably the insulation strip inside the door rather than the seal around the dishwasher. I ordered an insulation strip and it arrived a couple days later. I removed the seven screws of the interior door cover and disconnected the electrical. After removing the old insulation strip and installig the new one I reconnected the electrical wiring/plugs, put the door cover back on, and reinstalled the screws. Total time was about 15-20 minutes and the leak stopped. It was very easy and saved the cost of a repairman or a new dishwasher. I'm very glad that I "listened" to others and went with the new insulation strip.