DDW361RAW-PDDW361RAW0 Amana Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from MILPITAS, CA
- Parts Used:
- WPW10116811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper spray arm won't stay attached to dishwasher ceiling
remove damaged retainer clip. Install new one. Note: the upper spray arm screws onto the ceiling of the dishwasher with a reverse thread. That is, you need to turn it counter-clockwise to tighten it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shan from Medford, OR
- Parts Used:
- WPY912709, WPW10117748, WP902899
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Detergent cup wouldn't open/Leak along bottom of door
Replace wax timer for detergent cup. Replaced foam insulation at bottom of the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Nashville, AR
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water leak around door of dishwasher
I removed the gasket from the packaging & soaked it in hot water for approx 5 minutes to enhance the pliability of the rubber. I them opened the dishwasher door and removed the existing gasket, making sure I observed any specifics of the gasket, (ie...shape of gasket). I then cleaned any debris from the gasket channel. I took the new gasket from the water and folded it in half to determine where the middle was, and I started inserting the gasket beginning at the middle area of the channel, (just under the door latching mechanism). I finished inserting both sides and then closed the door for approximately 30 minutes to complete the gasket seating process. No leaks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ED from AVENTURA, FL
- Parts Used:
- WP912653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door spring linkage broken
Un screwed the dishwasher from the underside of my kithcen counter. Removed the copper water hose(after turning off water valves). PUlled the dishwasher from under counter to expose the hinges. Hung the new linkage on the hinge. Stetched the spring from flange on the bottom of the dishwasher to the new linkage. Reattached hose and reconnected the unit to counter top. Job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Ann Arbor, MI
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Leaking dishwasher door
I first replaced the seal/grommet around the soap dispenser latch, which was leaking, but did not totally stop the leak. I ended up ordering the door gasket too. Both were very easy to replace. My wife wanted a new dishwasher, but let me take a crack at fixing the leak first. Woo Hoo - big $$$ saved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Redmond, WA
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water on floor under dishwasher
The problem would rarely happen if the dishwasher was fully loaded vs. lightly loaded; which would produce a lot of water rapidly during the spray cycles. (or empty during the house inspection!). Removing and replacing the door gasket is super-easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from BURLINGTON, WI
- Parts Used:
- WP903093
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheel axle had broke and the wheel was not connected.
Actually following the online video is the way to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from MURRAY, UT
- Parts Used:
- WP902894
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
It was leaking out of the front door of the dishwasher
Pride old gasket out with screw driver easily removed it cleaned where the gasket was with mild detergent and easily installed new gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis Van from LODI, WI
- Parts Used:
- WPW10116811
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old spray arm broke
held spray arm to arm connector and replaced snap retainer, works like a new machine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lake Zurich, IL
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door gasket leak
just pulled out old gasket
pushed in new one
pushed in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Westminster, CO
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water leak from the lower area of the door opening
The repair went great. Very simple process to remove the old gasket and just press the new one in by hand. Total time to repair was 3 minutes. This was a very easy process, only needed to use a screw driver and my fingers to do it. The water leak was over. Anyone can do this repair. Don't think about getting a new dishwasher, or a plumber, as this is a very
simple repair that will easily do the fix!
simple repair that will easily do the fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elinor from VLY COTTAGE, NY
- Parts Used:
- WP6-903123
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rinse aid plastic burned and curdled
order replace part easy to use
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from AMISSVILLE, VA
- Parts Used:
- WP99002560
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dishwasher was overfilling
Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MORGANVILLE, NJ
- Parts Used:
- WP912653
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The plastic linkage that connect the spring to the door broke
The time to hook up the spring was a minute or two. I simply attached the linkage to the door and then attached the spring to the linkage.The extra time in the repair was re-attaching the cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lester L from Edmond, OK
- Parts Used:
- WP912653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Broken Door Spring Linkage
Turned off the water. Disconnected the water supply line. Extracted 2 screws holding the dishwasher. Pulled out the dishwasher. Changed out the nylon spring link. Pushed the dishwasher back into place. Reattached the water line. Turned the water back on.
Spring linkage and postage about $15.00.
Savings on service call and parts about $175.00. What a deal. Thank you PartSelect.
Spring linkage and postage about $15.00.
Savings on service call and parts about $175.00. What a deal. Thank you PartSelect.
Was this instruction helpful to you?
Thank you for voting!