ADB3500AWS36 Amana Dishwasher - Instructions

All I had to do was litterally snap the wheels into place..it was so easy and so cheap!

Removed screws. New Part does not come as an assy. Need to order handle. Other sights offer full assy for less.

Removed ~12 screws holding the inside liner onto the door. Pulled off the two connectors (one with black and one with white wires). Replace the handle and latch mechanism. Redid connections and replaced screws. Viola. (Be sure to buy BOTH the handle and latch mechanism- I don't see how you could easily install the handle on the mechanism myself, and what broken in my case was the black handle).

The upper arm assembly removes easily by unsnapping a plastic part or two that holds it in place.
Once the arm assembly is removed, you simply remove the screw that holds the arm on, replace the arm, and replace the screw. The key thing here is that you need a "star drive". This is a screw driver or bit that has a star shaped end. I don't know what size it is.

The plastic wheels on the upper and lower racks keep breaking. The latest casualty was also chewed up by the dog(s). They just pop right on the posts, a simple 2-second fix. I ordered the parts on a Tuesday morning, standard shipping, and they arrived FedEx less than 24 hours later. They came from Peoria, and I live about 1 hour away in Bloomington. Very pleased with the service. Will order from PartsSelect again if I need parts for any other appliance that I can fix myself.

After receiving the latch assembly, which arrived rather quickly, I found the handle itself was not enclosed in the package. Therefore this repair was delayed and after several calls to the 1-800 number I was informed the company had discontinued the distrubution of the handle. They offered a full refund, however I'm still waiting for the return labels so as to ship the latch back.

Now on the brighter side, the company representative put me in touch with a local distributor that did carry the latch/handle assembly as one piece and for a lot less money.

For those who are attempting the repair, don't worry, It was very simple. Just remove hex screws, lift the inside panel, unplug the two connectors and insert the new assemply.

Must say my wife was very happy to have the dishwasher up and running again.

Good luck !

This couldn't have been easier. After unsnapping the docking station from the dishwasher, I aligned the two flapper valves that come with the unit and pressed them into place. I then pushed the new unit into place by pushing first on the left side and then the right until it clicked into place.
I looked at the old one and found that one flapper was gone and the gaskets were deteriorated. What made the whole process easier was buying from PartSelect. I have bought from them before and will again.

Snapped new roller on to dish basket frome

I removed the screws from inner door panel.The 2 top screws also hold the latch assembly in place.I then lifted the panel, removed latch assembly, unplugged the 2 wires ,then installed new part in reverse order. Reinstalled screws in inner panel. Oh yes,first turn off power first at breaker box.

Removed end caps on guide rails of rack, slid upper rack out of dishwasher, popped off broken wheel, snapped on new wheel, slid rack back into guide rails and snapped in end caps of guide rail. Very easy to do.

took the broken ones off and snapped the new ones on.
easy as pie. took less than 5 mins.

Pulled out the dishwasher and disconnected two power wires to heater, turned off the two hold-down nuts and removed old heater. I then installed the new heater in reverse.

n/a

We unscrewed the inner door panel and pulled it apart, disconnected the wiring, removed the screws holding the dispenser in place and swaped it out. One problem we had putting everything back together was that the latch for the door didn't line up and we couldn't shut the door but we simply unscrewed the door, readjusted the latch and put it back together. Works great now!

First, turn the power off to the dishwasher. Then removed several screws that hold the panel in place. These are mostly on the side of the panel door. I then pulled the old panel and put the new one in.