C2557*0 Roper Cooktop - Instructions

ordered and replaced heater element, did not fix the problem so ordered thermal fuse and cycling thermostat when it arrived installed them still did not work. Went to the next item on list thermal cutoff kit ordered it, when it arrived installed and BINGO!!! It works... $107.00 later a dryer that works!!!!!

Replaced the heating element. Everything copacetic.

it was easy to replace the element

With the power cord disconnected, of course, I removed the rear panel. I used an ohmmeter to check temperature switches and heating element. I did this by removing the wires from the switch, and touching meter leads to each terminal on the switch. When the reading showed 0 ohms, I knew the switch had continuity and was ok. There are three switches to test. If the heating element temperature switches are bad, then the heating element will not work. I found all switches to be ok. I then removed wires from element and tested. No change in reading when leads were touched to terminals. I removed the one screw that holds the heating element housing on and removed the assembly. Removed the element from the housing and checked the coils. I found a break in the coils. This sounds like a lot of time, but, it only took about 15 minutes to do all of this. The element only took a couple of days to arrive. I vacuumed all lint from dryer,installed the element,and assembled dryer in about 15 minutes. It works great. I think it took longer to find and order the part than it did to repair. The part, including freight , was about $30. That's a heck of a lot better than $500 or more for a new dryer! P.S. If you're worried about remembering where any of the wires go, just take a picture before you disconnect anything.

Remove the screws from back cover to remove it.
Remove the two philips screws of the filter on top of dryer, to open top cover.
Once open, remove the screw that holds the heating element housing.
Unplug the terminals from heating element.
Unscrew the heating element from its housing.
Replace the heating element.
Screw on the opposite way you disarm the dryer.

I replaced the heating coil and the dryer works perfect. Thanks for the quick service in shipping the parts to me.

Everything wears out with age. This is the second element I have replaced on this dryer. The time is fast approaching the dryer too will go the way side. For now, though, we just keep her going as best we can. Simple installation using simple tools. Safety first, unplug the unit. Make comfortable room to work on it from behind. Remove the back panel, push the top off and unscrew the retainer. Remove the bottom retainer screw and the two wires on the element itself. All you have to do now is lift the element case off the bottom bracket, remove the old element and replace with the new in reverse order. Viola! Be cautious of your new drying times. It seems a fresh element brings new life to drying your clothes. We have found it has been cut by more than a third time. As a side note; bring the shop vac out to suck away all the lint that accumulates inside. Fire hazard for one, deterant to life of machine also. You don't have to be an electrical genius either. If it comes down to that type of repair....Better call a repairman! =0)

Aser your instructions I ordered and replaced the elemateand now it is back to normal. Much thanks

Replaced Heating Element Works Fine Timed Dry Works Perfect But Auto Dry Has Heat Drys Clothes Fine But Won't Turn Off Dial Does Not Move Any Sugestions

Turn off and unplug dryer, pull dryer away from wall to allow a decent working area. Remaoved use multi meter to assure no current flow, disconnect wires/remove at contact points. Remove panels and screwsnto expose heating element. Continue to remove screws from heating element, the only problem I had was reaching the top screw the is on the inside. I was able to squeeze my hand through an opening with a short/stubby flat head screw driver.

There are adequate repair examples in the forum especially one with the video. Pick one that you are confortable with and follow the guidelines remembering where the screws came out of off and using the magnetice extender to hold the screws removed. The video on the site was very helpful - the delivery time by partselect.com was impeccable.

i wasnt down stairs when my brother did it he took it apart and put it back together. my brother know all about fixing things hes a machanic