C2557*0 Roper Cooktop - Instructions

My son did the repair and thought it went very well. You saved me about $400 to $800 in that I didn't have to buy a new one. You got this part to me in 48 hours and I appreciated your timely manner. Your service is great! Thanks MZ

Removed the back,and a few screws through the top that held the filter sleeve in.
That allows enough room to reach in under the top, and unscrew the one screw that holds the element housing in place at the top.
Lifted the housing out after disconnecting the wires to the sensors and element.
Removed the element and replace it with the new one.
All of the electrical connectors slid right on the new element and put it back together.
Everything works fine.
Spent more time cleaning debris out of the dryer while I had it apart than replacing the part.
As usual Parts Select came through with the right part delivered to my door the next day, after ordering.
Thanks

Remove screws at lint filter, open top of dryer. Remove hex screw holding top of element casing. Slide dryer away from wall, remove 5 hex heads from rear panel, exposing element casing. Remove two screws holding sensors, and move aside. Lift dryer casing slightly and pull towards you to disengage from rear panel. Turn over and remove srew holding element to casing at bottom. Slide element out, and unplug two wires, noting position of each wire. Reverse procedure to reinstall element. Dryer works better than it has for years !

ordered on-line monday recieved on tuesday wife drying clothes tuesday evening--------just took out old element and hooked up new one --- very easy

I removed the back panel and took the 2 screws out at the lint screen, lifted the top back so I could remove the bracket holding the heating element can. After this was completed I was able to remove the heating element and install the new one, I had to cut the old connectors off and wire nut the new connector together. After this part was completed I reinstaaled the heating element can, secured the top back down,reinstalled the the back panel and pluged it in and wa-la it worked. I also wanted you to know that your prices are about $ 7.00 less than a few of the other part sites I checked on line and one of the sites even said that the part I needed was no longer available. I am sure glad that I kept looking and found your site because you saved me from buying a new dryer, thank you and if I get asked where to get parts I will recommend PARTSSELECT.COM.
Fred

Located heating element at PartSelect easily.Worked perfectly

With the power cord disconnected, of course, I removed the rear panel. I used an ohmmeter to check temperature switches and heating element. I did this by removing the wires from the switch, and touching meter leads to each terminal on the switch. When the reading showed 0 ohms, I knew the switch had continuity and was ok. There are three switches to test. If the heating element temperature switches are bad, then the heating element will not work. I found all switches to be ok. I then removed wires from element and tested. No change in reading when leads were touched to terminals. I removed the one screw that holds the heating element housing on and removed the assembly. Removed the element from the housing and checked the coils. I found a break in the coils. This sounds like a lot of time, but, it only took about 15 minutes to do all of this. The element only took a couple of days to arrive. I vacuumed all lint from dryer,installed the element,and assembled dryer in about 15 minutes. It works great. I think it took longer to find and order the part than it did to repair. The part, including freight , was about $30. That's a heck of a lot better than $500 or more for a new dryer! P.S. If you're worried about remembering where any of the wires go, just take a picture before you disconnect anything.

Turn off and unplug dryer, pull dryer away from wall to allow a decent working area. Remaoved use multi meter to assure no current flow, disconnect wires/remove at contact points. Remove panels and screwsnto expose heating element. Continue to remove screws from heating element, the only problem I had was reaching the top screw the is on the inside. I was able to squeeze my hand through an opening with a short/stubby flat head screw driver.

There are adequate repair examples in the forum especially one with the video. Pick one that you are confortable with and follow the guidelines remembering where the screws came out of off and using the magnetice extender to hold the screws removed. The video on the site was very helpful - the delivery time by partselect.com was impeccable.

i wasnt down stairs when my brother did it he took it apart and put it back together. my brother know all about fixing things hes a machanic

Remove the screws from back cover to remove it.
Remove the two philips screws of the filter on top of dryer, to open top cover.
Once open, remove the screw that holds the heating element housing.
Unplug the terminals from heating element.
Unscrew the heating element from its housing.
Replace the heating element.
Screw on the opposite way you disarm the dryer.

Replaced Heating Element Works Fine Timed Dry Works Perfect But Auto Dry Has Heat Drys Clothes Fine But Won't Turn Off Dial Does Not Move Any Sugestions

Aser your instructions I ordered and replaced the elemateand now it is back to normal. Much thanks

I replaced the heating coil and the dryer works perfect. Thanks for the quick service in shipping the parts to me.

Everything wears out with age. This is the second element I have replaced on this dryer. The time is fast approaching the dryer too will go the way side. For now, though, we just keep her going as best we can. Simple installation using simple tools. Safety first, unplug the unit. Make comfortable room to work on it from behind. Remove the back panel, push the top off and unscrew the retainer. Remove the bottom retainer screw and the two wires on the element itself. All you have to do now is lift the element case off the bottom bracket, remove the old element and replace with the new in reverse order. Viola! Be cautious of your new drying times. It seems a fresh element brings new life to drying your clothes. We have found it has been cut by more than a third time. As a side note; bring the shop vac out to suck away all the lint that accumulates inside. Fire hazard for one, deterant to life of machine also. You don't have to be an electrical genius either. If it comes down to that type of repair....Better call a repairman! =0)