CSG9900AAB Maytag Cooktop - Instructions

removed 2 screws to access the ignitor. Discinnected the wires from the old ignitor and slid the old ignitor off. Installed the new ignitor and attached wires.

The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it easy to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.

Since the other three burners sparked, I traced the problem to the switch on the valve shaft. To replace, (after unplugging the power cord) I pulled off the knobs, removed the two screws on the valve cover (inside the downdraft vent) and pulled the switch up the shaft to remove. I transferred the spade terminals to the replacement switch, oriented and installed.

None of the surface burners (two Uni-burners) would light without using a match. I first ordered two replacement PS2089818 top burner spark electrodes. I replace one which was very easy - the electrode just clips into the burner - and I traced the wires down to the back bottom of the stove where I found they plugged into an ignition module. The new electrode didn't help, but since all four burners were out it made sense that the ignition module would be the problem and not the two separate electrodes. So I ordered a new ignition module. It plugged in easily with the terminals well marked like the original. I put the original electrode back in and all four burners now light properly with the desired "tic tic tic" sound with the knobs in the "high/light" position.

I removed the burner knobs, unscrewed the 2 screws and removed the cover. I pulled the old switch off the stem and removed the wires. I reconnected the wires to the new switch and pushed it in place on the stem. After checking to make sure the new igniter switch worked, I replaced cover tightened the 2 screws and replaced the knobs. Job done in 5 minutes!

disassemble housing and remove fan and motor. Reatach fan to new motor, connect wiring, place gasket around motor and reassemble.

Unplug and pull range away from wall.
Remove metal panel from back of range by using nutdriver to remove 4 screws.
Use phillips scewdriver to remove 2 screws holding old spark module.
Unplug 4 wires from spark module and note placement of wires for reinstall.
Install new module by reversing procedure.
Slide range back against wall and plug in.

Entire process took less than 30 minutes.

NOTE: Spark Module received from partselect.com did not match old part exactly. The screw holes on the new part did not line up with screw holes from old part. I reinstalled new part with just 1 screw. Was told by partselect customer service that the part I received had been substituted and would work fine. It does work but it did not fit correctly.

The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.

unscrewed previous unit, placed new unit and screwed in place.

Removed old burner, replaced with new one, works perfectly! Only one screw to take out and use with new piece.

So very easy!!!! I'm a 70 year old grandmother with a small socket set - and that's all I needed! Removed one small screw, removed old burner, popped new burner in, replaced one screw, and back in business! Placed order, received it in 2 days, fixed burner. So much faster than calling a repairman!

Turn off the gas supply and unplug the electric supply. Remove the top grates and the burner cartridges. Remove 12 screws around the top cover and loosen the two screws for the fan switch. Pull the fan switch up and out of the way, remove the top cover. With a marking pen, label the four igniter switches and pull them off the gas valves. From underneath, remove the gas line from the pressure regulator, then remove the regulator from the pipe coming from the circular manifold. With a 3/16 socket (1/4 inch drive) or a 3/16 nut driver, remove the four screws that hold the manifold. Then from the top pull the manifold up and out. On the bottom, remove the screw (1/4 inch socket or nut driver) and remove the old gas valve. That's it. Now just put it all back together in reverse order. I used pipe joint compound on the pipe threads. Check for leaks with a soapy water solution. If I had to do this again, it would only take me half the time. I wasn't sure how everything came apart the first time..

The spare part came within two days after I place the order on line. I drew a simple wire diagram of the faulty switch-regulator. Shut off the power to the stovetop, before removing the four terminals on the faulty switch-regulator. I pushed the old regulator up from the center pin and replaced it with the new regulator. The next step was to reinstall the four wire terminals using my wire diagram. Final step was to turn the power back to the stovetop and test the new switch-regulator.

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.