X8261RV Maytag Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from Fenton, MI
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Flame coming from under burner cap
Unplug power, put strap wrench around burner cap and turn counter clockwise 1/4 turn, remove 2 wires, installed in reverse.took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from San Francisco, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No ignition of gas stove burner
Ordered the part, removed the wires (by light pulling) from the old burner and inserted them in the new one. Tried it, and it worked. Total work time, about 5 min. Amount saved, $150.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerald from Loveland, OH
- Parts Used:
- W11170853
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench (Adjustable), Wrench set
Missing regulator when floor model gas cooktop was purchased
1. Apply gas pipe joint sealer to treaded nipple on bottom of cooktop; 2. Install regulator on nipple with regulator direction arrow pointing to top of cooktop; 3. Tighten but do not overtighten as it may crack the aluminum body regulator; 4. Make sure the face of the regulator with the green painted surface faces the outside of the cabinet; 5. Get a new gas flex hose to connect to gas pipe (got mine at Lowe's - 2 feet long with all the right fittings for about $15). 6. Follow instructions on gas flex hose - make sure you use gas pipe joint sealer only where indicated; 7. Turn gas shutoff valve back on and test for leaks using soapy water; 8. Turn on each cooktop burner to bleed out air.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Midwest City, OK
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old burner's flame was coming out below the burner.
1/4 turn counter clockwise to remove the old burner, removed wires. Placed wires on new burner tightened them with pliers,dropped it in, 1/4 turn clockwise--done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Mobile, AL
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Gas blowing out from under burners
As the video said, twist burner to the counterclockwise 1/8 turn. Lift the burner straight up. Disconnect the two wires. Remove the burner and reconnect the wires ( they only go one way so they cannot be connected backwards.) Place the burner over the gas fitting and turn the burner clockwise until snug. I turned the power off at the circuit breaker box. The video was extremely helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corliss from Oakland, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the old had rust out and gas was sipping from the side
I removed the old burner with pliers took off the electrodes. Replace the new burner attach the electrodes placed it back in the burner slot and now it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Aberdeen, MD
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
power boost burner went up and all my burners got very rusty on the underneathe side
We were at a loss for a long time without my boost burner and then while checking all the rest of the burners my husband discovered that all of them had a massive amount of rust on the underneathe side of the burners and that worried me. Well as usual my husband took care of my worries when he discovered Parts Select. We both were pleasantly surprised when we found out that you had what we needed. And the installation was less than 5 minutes, WOW, THAT WAS GREAT! Thanx a million!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Floral park, NY
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
the top broke away it was corroded
use the pliers. to get. the remaining half off and the screwdriver to cleen the rest of the rust off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bhavni from Richmond, TX
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burners won't light up
We received the burners we ordered in timely manner, and it was very easy to install. Just unhook the old burners and drop the new ones in and connect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Lompoc, CA
- Parts Used:
- WP3424F005-81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I replaced the four Drip Pans on our Cooktop.
It was simple to remove the parts and then remove two screws and clean the area and re-assemble with the new drip pan. It was easier than I though it would be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Santa Barbara, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old burner was rotten and leaking
Pulled up the old burner, disconnected the ignition wires, re-connected them to the new burner, replaced the new burner in the stove and presto - everything worked as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete di from San Diego, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old burner rusted, flame bypassing
Simply twisted to remove from range top, slipped off igniter wires, attached to new burner, and twisted back into place on range top. Works great,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Oconto Falls, WI
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner flame was poor and yellow flames left sute marks on pots and pans
twist old burner and lift out disconnect two wires throw away gasket (if there is one left) connect two wires to new burner set in and twist till tight total time 45 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from Tomahawk, KY
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner rusted flames coming out the side of the burner
turned the old burner to the left and lifted it out. unpluged the wires with a screwdriver pluged the wires into the new burner and putit back on the stove and turned it to the right
Was this instruction helpful to you?
Thank you for voting!