KECS160SWH0 KitchenAid Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Craig from Bangor, PA
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner would not heat
Took the old burner out and inserted the new one. The burner was received two days after ordering. I was very satisfied with the service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Rochester, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
old bowls could not be cleaned. These new bowls make the stove look great
Removed old bowls and replaced with the new bowls. Also, thanks for your help with the rang knobs. You did not have the replacement knobs for my range but you gave me help in where I might get them. With the new bowls and knobs the range looks like new. Thanks again for all your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Union Mills, NC
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not heat up the connection was bad
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Desoto, MO
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
two of the burners were working intermittently
I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Indianapolis, IN
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace bowls
Removed old bowls and replaced with new ones. Easy. Piece of cake. Perfect fit.thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Chicago, IL
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner stopped heating up.
Searched the internet for the replacement part, placed the order and then disconnected the old one and inserted the new burner prongs into the socket. Worked perfectly!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rev Connie from Mattawan, MI
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement drip pans didn't fit -- wrong type
Purchased appropriate drip pans here. They arrived overnight, much to our surprise! The range elements were easy to remove, and the drip pans fit precisely as they were designed to do. Ta Da! repair completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Tucumcari, NM
- Parts Used:
- W10196405RW, WP3177565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner element partially heated
Pulled out old one, plugged in new. Replaced Drip bowl as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from EL DORADO HILLS, CA
- Parts Used:
- WP3177565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
power burner warped, welds broken
just pulled and removed the old burner then pushed the two new power connections into same place - no tools - works perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Albany, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my drip bowls were old an I was unable to clean them
I took the old drip pans out and replace them with the new ones. Now my stove looks brand new. These were a perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Phoenix, OR
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls, tried prepackaged from box stores
After putting up with ill fitting generic versions of our drip bowls, we smartend up and ordered correct parts. They went in super easy, perfect fit and the heating element is now perfectly level. Who knew that following the manufactors recommendations to buy correct parts would make such a difference? Well we know now! Thank you. The parts were shipped almost immediately and delivered as promised.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Walnut, CA
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip pans missing
placed element in drip pan and plugged in. .Fit perfectly.I am very pleased with the product and service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Staunton, IL
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner keep coming on and going off had a short in burner plug-in block.
Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Saranac Lake, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bowls had burnt on food
replaced them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Chesapeake, VA
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The surface burner socket that the burner plugs into melted.
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.
Was this instruction helpful to you?
Thank you for voting!