KECS160SWH0 KitchenAid Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Phillipsburg, NJ
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wire broken off plug in block
Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irina from Green Cove Springs, FL
- Parts Used:
- W10196406RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ugly looking drip bowl.
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Tucson, AZ
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner replacement
Pug it in! That's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Versailles, IN
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
large burners not working
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dicky from mcrae, AR
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace burner coil connector
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Edgewater, MD
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Drip Bowls
Lifted out the old ones and inserted the new ones and my range top looks brand new now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Viroqua, WI
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
none
I pulled out the burners, cleaned up the crumbled drip pans ,installed the new drip pans, pluged in the burners and was finished in about 3 minutes. I will order again from you. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Kasson, MN
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Surface burner block corroded
It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail M from Lockport, NY
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner was slow heating at times. Moved back burner to front still same thing.
Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Pinellas Park, FL
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wrong replacement Drip Pans installed previously caused damge to 8" Burner.
Removed burners and drip pans, replaced drip pans and re-installed burners. Simple....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Brookfield, CT
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner failure
Removed and replaced burner unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- judy from coarsegold, CA
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner fell apart
Just plugged it in and away I went.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATRICIA*NAYLOR from NEW PRT RCHY, FL
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Generic Drip Bowls Made The Burners Tilt.
Pulled out the generics and popped in the correct bowls for my whirlpool. Done in less than 10 minutes and perfecto,. . . Level burners :-) thanks we'll be back when we need you again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Spring HIll, FL
- Parts Used:
- W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner didn't work because it had the wrong drip bowl
Replaced the drip bowls, very simple. Excellent delivery time, ordered them Saturday, delivered Tues morning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from Falls Village, CT
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner stopped heating
Unplugged the old one and plugged in the new, which you sent promptly. No tools. Easiest fix ever.
Was this instruction helpful to you?
Thank you for voting!