9114282590 Kenmore Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from FOUNTAIN, CO
- Parts Used:
- WB17X5113
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Terminal block wire had burned out
Unplugged the range. Opened the range top, unscrewed the old block and cut the wires back. New mount did not match the range top. Removed the old mount from the old terminal block and removed the new mount from the new terminal block and inserted the new block in the old mount. Spliced the wires with the provided wire nuts, protected the splice with the provided heat shrink tubing and installed the burner in the new terminal block. Reinstalled the power cord and tested the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda L from Naples, NY
- Parts Used:
- WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted out drip pan
unplugged the element took the old pan out and put the new one in, plugged the element back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from San Diego, CA
- Parts Used:
- WB17X5113
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burners on range would occasionally fail to heat
First I disconnected the power. Then I removed the burner element and drip pan. Using the screwdriver I removed the single screw that holds the terminal block in place. I then cut the 2 wires to the old terminal block. I connected the wires of the new block to the existing wires using the supplied wire nuts. Next I slipped the supplied heat shrink tubing over the wire nut and wires and using the heat gun I applied heat to the shrink wrap. Finally I reinstalled the new terminal block using the old screw and re-installed the drip pan and burner. I repeated the procedure for 2 other burners that were exhibiting the same problem. All work perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara A from Riverhead, NY
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced the drip bowls
I am not going into a description. It is a very minor thing to do. I did appreciate the quick delivery of the parts and will purchase future appliance parts from you again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alicia from harrison, NJ
- Parts Used:
- WB17X5113
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
terminals was burned
i removed it and installed the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from Orient, NY
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
bowls were worn
Just removed the elements and inserted the new drip pans. Could not have been easier.
Was this instruction helpful to you?
Thank you for voting!
Porcelain drip bowls slots for unit to fit in was eroded
Simple ! I unplugged the units,removed the old drip bowls and replaced them with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Richmond, VT
- Parts Used:
- WB17X5113
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Range element working intermittently then failing completely
Remove the element and pan. Unscrew the bracket holding the old terminal. The terminal has adequate wire to pull out. Found area where insulation wasn't brittle. Cut old wires and stripped them to expose 1/2 inch of wire. Attached wires from new terminal with wire nuts. Placed heat-shrink tubing over each assembly and shrank it with a heat gun. Retained the bracket from the old terminal, since it looked like it would hold the terminal assembly a bit more firmly than the new bracket. Reassembled in reverse order. Presto -- once again disappointing my wife in her desire for new appliances!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Miami 33166-2667, FL
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
All drip bowls broken or rusted
Just pull out the heat element, place the new drip bowls and then insert again the heat element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Guilford, NY
- Parts Used:
- WB17X5113
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My heating element will not work
I turned the power off to the stove (very important). then I unplugged the heating element from the terminal. I then unscrewed the terminal from the range top and pulled the terminal through to expose enough wire to do the job. I then proceeded to cut one wire from the old terminal and twist the new wire onto the wire that goes to the switch. Then I capped it off with the electric cap that came with the new terminal. then I covered the exposed wires with the sleeve that came with new terminal. Then I did the same exact thing for the second wire. After that was all done I put everything back together and turned the power back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Frederick, MD
- Parts Used:
- WB31K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Existing drip pan was burned & beyond cleaning.
Unplugged the burner unit. Removed the existing drip pan. Installed new drip pan in place & re-plugged the burner unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Morgan City, LA
- Parts Used:
- WB27X5487
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Blower not working correctly.
Turned off the power to the stove top and remove the blower capacitor installed the new capacitor. Turned the power back on and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- willie from Columbia, SC
- Parts Used:
- WB32X5058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate Burned Up
I simply entered name of product and what I needed. You said I'll get on 12/28/09 but I actually received it 12/20 or 12/21. It's perfect. I'm pleased. Thank you so much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cary from hermitage, TN
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could not find the proper fitting drip pans.
Got the right ones from you"could not get them at Sears.com". All is well, wife is happy again.
Was this instruction helpful to you?
Thank you for voting!