9114282790 Kenmore Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Victoria from Atwater, OH
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out terminal block
It was as easy as you said. I took the back off, removed the screws holding the terminal, un-hooked it and put the new on on. Replaced the back and wa-la! Working burner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Canandaigua, NY
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
top burner terminal block burned put due to heavy use
Disconnected power supply to range, pull top back metal cover, pull wires from burner on/off switch,and removed one screw that holds block in place. Installed new terminal block by placing screw back on block & placing wires back on the on/off switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Frederick, MD
- Parts Used:
- WB31K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Existing drip pan was burned & beyond cleaning.
Unplugged the burner unit. Removed the existing drip pan. Installed new drip pan in place & re-plugged the burner unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Morgan City, LA
- Parts Used:
- WB27X5487
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Blower not working correctly.
Turned off the power to the stove top and remove the blower capacitor installed the new capacitor. Turned the power back on and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from Greenville, MS
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The Surface Burner Over Heating
Replacing the Surface Burner Terminal Block Kit was very easy.
1. Pull the stove from the wall a little so you can have space to work. I unplug the stove from lthe 220 outlet. Then remove the Surface Burner element.
2. Then we removed the back pannel from the stove by removing the screws with a nut driver. Only four screws to remove.
3. Once the pannel was removed. I Unpluged the wires from the stove pannel. Being careful not to damage the plug in. There were only two wires to unplug. So trace the wires to make sure you are unpluging the correct one.
4. Lift the top up on the stove and unscrewed the Terminal Block from the top of stove. We only have one screw there.
5. Pull the Terminal Block and wires out and replace with the new Terminal Block, making sure the wires were feed along the side under the top of stove so they can not be damaged. Plug in wires and replace pannel.
1. Pull the stove from the wall a little so you can have space to work. I unplug the stove from lthe 220 outlet. Then remove the Surface Burner element.
2. Then we removed the back pannel from the stove by removing the screws with a nut driver. Only four screws to remove.
3. Once the pannel was removed. I Unpluged the wires from the stove pannel. Being careful not to damage the plug in. There were only two wires to unplug. So trace the wires to make sure you are unpluging the correct one.
4. Lift the top up on the stove and unscrewed the Terminal Block from the top of stove. We only have one screw there.
5. Pull the Terminal Block and wires out and replace with the new Terminal Block, making sure the wires were feed along the side under the top of stove so they can not be damaged. Plug in wires and replace pannel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- willie from Columbia, SC
- Parts Used:
- WB32X5058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate Burned Up
I simply entered name of product and what I needed. You said I'll get on 12/28/09 but I actually received it 12/20 or 12/21. It's perfect. I'm pleased. Thank you so much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Emmett, ID
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Terminal replacement
The wire to the burners were old and needed replacement. When the new terminals arrived, my husband had gone hunting. When the parts arrived, I pulled the stove away from the wall and found the nut driver that I needed. I removed the screw on the terminal box under the burner and realized I had to remove the back panel of the stove. I unplugged the old wires and plugged in the new ones. I installed the new terminal boxes under the burners and plugged the burners back in. My stove works like new and I am thrilled that it was so easy. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mirtes from Marlborough, MA
- Parts Used:
- WB17X5113
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heating element not heating
Removed the terminal block. Cut the wires. Cut the sheathing to expose the wire. Connected the new wires with the old wires by twisting them together. Added the wire nut and reconnected the block. Tested ok.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deana from Crockett, TX
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new drip pans
I removed the burners, took the old drip pans out, put the new ones in and put the burners back in. This was so easy that a caveman could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Moses from Spring Valley, NY
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the burner did not get hot
First I shut off the breakers. I cut the wire from the end of the new part and took off the plastic off because the end of the new wire has a special end clamp to connect to the old wire which is in the stove but that wire didn't have the same clamp to be able to connect them together therefore I needed to cut the wire to from the new part also and connect it to the old wire with a wire nut which is on the range which is attached to all the other burners. Twisted them together and I put a wire nut to hold them strong together, pushed in the end of the burner into the 2 holes of this new part. I turned on the breakers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Wheat Ridge, CO
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burner Terminal had shorted out out.
had to pull range away from wall and unplug it so we could get behind to access the rear panel. we then removed old terminal block, by, removing screws from back panel, and one screw from under burner drip pan, inserted, new block, and reassembled. plugged it in to test and burner worked properly.
Was this instruction helpful to you?
Thank you for voting!
My drip pans looked terrible and I could not get them clean.
I took the old ones out and put the new ones in. No problems. Good fit. Looking back I should have ordered new elements as well but could not afford them now. I appreciate the ease of ordering and the speedy delivery of these items and will definitely use Part Select again when needed. Thank you for your assistance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from limerick, PA
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken surface burner terminal block[recepticle]
as described on video,with no problems,very helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Godfrey from Virginia Beach, VA
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Does not. The heating element sucket is crack and burn loss connection.
Replace the sucket for the heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cary from hermitage, TN
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could not find the proper fitting drip pans.
Got the right ones from you"could not get them at Sears.com". All is well, wife is happy again.
Was this instruction helpful to you?
Thank you for voting!