JGD8430ADF Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from Lakeside, Arizona, AZ
- Parts Used:
- WP74009336, WP8273062
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Igniter did not work
Bought The burner with the electrode already installed. The only way to go, since the screws will not come out without breaking. Also purchased two torx screws as thay also broke. A bad design by the manafactor.Had to drill and tap out for new torx screws to fit into the gas houseing. PartSelect had all the parts I needed. Dan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Two Rivers, WI
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Igniter Needed Replacement
Removed the burner & igniter as a unit. Screws holding burner down were very tight. One came out with effort, the other one the head broke off. Tried heat but to no avail. The screw holding the igniter had to be drilled out. Fortunatly I work in a machine shop so I was able to remove the screw, but the hole was then too large for the replacement screw. I wound aluminum foil around a toothpick to form a bushing in the hole so the screw could grab. Same principle as those plastic anchors for plaster or drywall. Bought stainless screws, but did not even try to get the broken screw out of the cooktop. The one screw holds it in place just fine. Wife is very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Franklin, TN
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Cook top electrode "starter" not working
Do not buy just the burner electrodes. The screws that hold the electrode will break off. Purchase the burner head with electrode. I would recommend placing anti-sieze lub on the new screw that holds the electrode to the burner head so if the electrode fails again it can be replaced. The screws that hold the burner head to the top top are mild steel and will rust and snap off. I would use a rust penatrent on these screws several days before trying to remove but most likely they will strip or break off. Replace all these burner head screws with stainless steel screws with anti-seize applied. If any of this sound difficult call a repair company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- grant from aurora, CO
- Parts Used:
- WP74009336
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Spark Ignitor replacement
Screws holding burner base and ignitor were plain steel. If they had been stainless they probably would not have rusted in so tight. One in the base broke off, and the one holding the ignitor could not be removed, even with heat from a torch. I ended drilling it out and re-tapping the hole. If I wasn't mechanically inclined I would have had to give up and order a new burner base.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Deer Park, IL
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Burner electrode was damaged during cleaning
A crack in the porcelain caused the spark to not go in the proper direction, therefore the burner would not ignite. To have the job done by a professional would have cost $200.00 plus parts. Remove two phillips screws lift the burner out then remove the one phillips screw that held the electrode. Then with the new electrode in place reverse the previous steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Olympia, WA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
igniter would spark, but not light flame
Installed new igniter, but would still not light flame. Determined it was a design flaw. On our range, the 2 right hand burners have "lift-off tops" that are farther away vertically from the igniter than the smaller left hand burners. I placed asmall nut from a nut-bolt assembly on top of the igniter, and now the igniter sparks higher to the "lift-off top" and the flame ignites everytime. Without that added heigt, the igniter just sparks uselessly around the base of the burner. There should be a higher igniter designed for the higher distance between the igniter and that removable top. Good luck with your own modification.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Dayton, OH
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner grate pads worn off or missing
I took a jewelers screwdriver and completely cleaned out what was left of the old pads. Then applied a small amount of heat resistant rtv sealant to each hole, slid in the new pads and wiped off the excess. I let everything set overnight. The next day everything was solid. Job was complete. Note I've done this before and did not get the results I did this time. I believe it was the instruction that came with the pads and the tip-off to use the rtv. Thank you PartSelect T.Garr
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Glenwood Springs, CO
- Parts Used:
- WP74009336, WP7733P410-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One burner not lighting, but has spark
Electrode ceramic was chipped. Spark was not coming to the top of the electrode, and stove would not light. Remove two burner screws. These are "baked" on...so use some liquid wrench first if you have it. Don't strip the head, or you'll have a mess. Remove burner, unplug electrode, remove electrode screw, replace electrode. Reverse process and you're good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Gilbert, AZ
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken plastic chrome knobs
bought new ones and pushed them onto D shaped posts total time 90 seconds they may break again in 10 years but I am to lazy to reinforce them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from dayton, WA
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original Burner Knob broke at the shaft
Simply took off the original knob and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann P from San Antonio, TX
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic burner knobs were split and would not let you turn burners off and on
I ordered an entire new set even though I only needed 2...removed all of the old ones, threw away the broken ones and installed the entire set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from nanticoke, PA
- Parts Used:
- 74007735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner porsclend was cracked and would not light
removed grate and cap.unscrewed burner plate.disconnected spark wire and replaced with new part.fired it up .now it workes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Harrisville, RI
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The female D stem fitting of the control knob cracked, we could not turn on / off or control temperature to that heated area.
We replaced the control knob with an exact replica from PartSelect at a very reasonable price – Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yosh from Mill Creek, WA
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner knob socket was broken
pull out the old knob and replace with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KARL from OCEAN, NJ
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner ignator split--
unscrewed old ignator---replaced w new--done deal!!!!
Was this instruction helpful to you?
Thank you for voting!